2,718
edits
Changes
Jump to navigation
Jump to search
Line 131:
Line 131: − + − ==== You need (for '''one''' Encoder PCB): ====+ − * 2 * rotary encoder with pushbutton (Pos. 17) − * 2 * 100nF capacitor (Pos. 8) − * 1 * multi-pin 6 pins wide (part of Pos. 24) − * 1 * multi-pin 2 pins wide (part of Pos. 24) − * 1 * encoder PCB (Pos. 19) − + + + + + + + + + − # '''Notice!''' Due to the mounting of the encoders on a front panel, the 6-pin-row must be soldered from the bottom of the PCB (pin numbering will be 1..6 from the lower side of the PCB!). '''The picture below shows the WRONG component side! (newer images will follow)''' − # The order of the following steps is not important: Solder the capacitors, the 2-pin-rows and the encoders to the board (on the upper side) - that's it. − # You have to do this twice - you need two encoder boards. − + + + + + + + + + + + + + + + + + + + + + + + + − Alternative: Mount the pin row at the bottom of the PCB:+ + + − +
→Step 2: Encoder boards
[[File:MIDI-socket_Solo.jpg|600px]]
[[File:MIDI-socket_Solo.jpg|600px]]
=== Step 2: Encoder boards ===
=== Step 2A: Controller Modules Dual (2 x dual encoder controllers) ===
'''Note:''' If you have the new Controller Single modules you must jump to the Step 2B.
[[File:Encoder_Parts.jpg|600px]]
==== You need (for '''one''' Controller Module): ====
* 2 x rotary encoder with pushbutton (Pos. 17)
* 2 x 100nF capacitor (Pos. 8)
* 1 x multi-pin 6 pins angle (part of Pos. 24)
* 1 x multi-pin 2 pins angle (part of Pos. 24)
* 1 x controller module PCB (Pos. 19)
[[File:controller_kit.jpg|600px]]
==== HowTo: ====
==== HowTo: ====
[[File:Encoder_Solo.jpg|600px]]
# The order of the following steps is not important: Solder the capacitors and the encoders to the board (on the upper side) - that's it.
# Solder the 6-pin and 2-pin-rows. '''IMPORTANT!''' Due to the mounting of the encoders on a front panel, the pin-rows connectors must be soldered on the bottom of the PCB. The 6-pin-row must have its pins as showed in the photo (pin numbering will be 1..6 from the lower side of the PCB!). For optimal case mounting, the 2-pin-row should be soldered with different orientation in each module. One with right-orientation and the other one with left-orientation.
# You have to do this twice - you need two encoder boards ;-)
[[File:controller_ensambled_01.jpg|600px]]
[[File:controller_ensambled_02.jpg|600px]]
'''Note:''' Mount the pin row at the bottom of the PCB. Look the photos!!! ;-)
=== Step 2B: Controller Modules Single (4 x single encoder controllers) ===
'''Note:''' If you have the old Controller modules, with 2 rotary encoders each, you must read the Step 2A.
==== You need (for '''one''' Controller Single Module): ====
* 1 x rotary encoder with pushbutton (Pos. 17)
* 1 x 100nF capacitor (Pos. 8)
* 1 x multi-pin 4 pins angle
* 1 x controller single PCB
[[File:4xcontroller_single_kit.jpg|600px]]
==== HowTo: ====
# The order of the following steps is not important: Solder the capacitor in the C1 position (right side) and the encoder to the board (on the upper side) - that's it.
# Solder the 4-pin-row. '''IMPORTANT!''' Due to the mounting of the encoders on a front panel, the pin-row connector must be soldered on the bottom of the PCB. The 4-pin-row must have its pins as showed in the photo (pin numbering will be 1..4 from the lower side of the PCB!).
# You have to do this 4 times - you need 4 encoder boards ;-)
[[File:Encoder-Pins-Down.jpg|600px]]
[[File:controller_single_ensambled_01.jpg|600px]]
=== Step 3: Pin row on the Hifiberry ===
=== Step 3: Pin row on the Hifiberry ===