Line 106: |
Line 106: |
| | | |
| https://discourse.zynthian.org | | https://discourse.zynthian.org |
| + | |
| + | ===Secure the Jack connectors=== |
| + | |
| + | Put the rings on the outer side of the case to avoid damaging the case surface when you tighten the nuts. |
| + | |
| + | [[File:IMG_2396.JPG|400px]] |
| + | [[File:IMG_2397.JPG|400px]] |
| + | [[File:IMG_2398.JPG|400px]] |
| + | |
| + | ===Secure the MIDI-IN/OUT/THRU connectors=== |
| + | |
| + | Just insert the connector with the JST-wire from the out-side of the case and the nut from the innerside. A pair of pliers can be useful for tighten. |
| + | |
| + | [[File:IMG_2400.JPG|400px]] |
| + | [[File:IMG_2401.JPG|400px]] |
| + | [[File:IMG_2402.JPG|400px]] |
| + | |
| + | ===Mount the MIDI activity LEDS=== |
| + | |
| + | Insert the 3 LEDS in the case holes. You may want to push the LEDs with something more rigid than your finger. The screwdriver's handle could be fine. |
| + | |
| + | [[File:photo-not-available.jpg|600px]] |
| + | [[File:IMG_2365.JPG|600px]] |
| + | |
| + | When it's done, you have to plug the 2 LED wires (red/black) with the 2 spare wires on the MIDI JST harness (green/yellow). Polarity is important, so don't cross the wires: |
| + | |
| + | * JST Green wire (1) => LED's Anode (LED's red wire/long lead) |
| + | * JST Yellow wire (2) => LED's Cathode (LED's black wire/short lead) |
| + | |
| + | [[File:photo-not-available.jpg|600px]] |
| + | |
| | | |
| ===Assemble the Main Computing Block=== | | ===Assemble the Main Computing Block=== |
Line 139: |
Line 170: |
| [[File:photo-not-available.jpg|600px]] | | [[File:photo-not-available.jpg|600px]] |
| | | |
− | ===Secure the Jack connectors===
| |
− |
| |
− | Put the rings on the outer side of the case to avoid damaging the case surface when you tighten the nuts.
| |
− |
| |
− | [[File:photo-not-available.jpg|600px]]
| |
− |
| |
− | ===Secure the MIDI-IN/OUT/THRU connectors===
| |
− |
| |
− | Just insert the connector with the JST-wire from the out-side of the case and the nut from the innerside. A pair of pliers can be useful for tighten.
| |
− |
| |
− | [[File:photo-not-available.jpg|600px]]
| |
− |
| |
− | ===Mount the MIDI activity LEDS===
| |
− |
| |
− | Insert the 3 LEDS in the case holes. You may want to push the LEDs with something more rigid than your finger. The screwdriver's handle could be fine.
| |
− |
| |
− | [[File:photo-not-available.jpg|600px]]
| |
− | [[File:IMG_2365.JPG|600px]]
| |
− |
| |
− | When it's done, you have to plug the 2 LED wires (red/black) with the 2 spare wires on the MIDI JST harness (green/yellow). Polarity is important, so don't cross the wires:
| |
− |
| |
− | * JST Green wire (1) => LED's Anode (LED's red wire/long lead)
| |
− | * JST Yellow wire (2) => LED's Cathode (LED's black wire/short lead)
| |
− |
| |
− | [[File:photo-not-available.jpg|600px]]
| |
| | | |
| ===Secure the Display=== | | ===Secure the Display=== |