2,705
edits
Changes
Jump to navigation
Jump to search
Line 76:
Line 76: − + Line 110:
Line 110: − + Line 127:
Line 127: − + Line 184:
Line 184: − + Line 318:
Line 318: − + Line 348:
Line 348: − + Line 360:
Line 360: − +
Building a Zynthian Box using an official Kit v3 (view source)
Revision as of 13:17, 13 January 2020
, 13:17, 13 January 2020→Test the Controllers & UI
===Zynthian Bundle All Kit v3===
===Zynthian Bundle All Kit v3===
A Zynthian Kit is a set of electronic parts. The ''official'' Zynthian Bundle All Kit v3 consists of specific parts:
A Zynthian Kit is a set of electronic and mechanic parts. The ''official'' Zynthian Bundle All Kit v3 consists of these specific parts:
+ '''4 x Controller Modules + Wiring'''
+ '''4 x Controller Modules + Wiring'''
===Prerequisites===
===Prerequisites===
Assembling your Zynthian Kit V3 is not difficult at all: you need is your attention, a screwdriver, and an adjustable wrench. You don't need to solder anything, just put it together and connect the wires.
Assembling your Zynthian Kit V3 is not difficult at all: you need your attention, a screwdriver, and an adjustable wrench. You don't need to solder anything, just put it together and connect the wires.
Read the instructions and observe the detailed photos carefully. If you get in trouble you can ask the community:
Read the instructions and observe the detailed photos carefully. If you get in trouble you can ask the community:
===Secure the MIDI connectors===
===Secure the MIDI connectors===
Insert each MIDI from the outside and secure them with the bolt from the inside.
Insert each MIDI connector, from the outside and secure them with the bolt from the inside.
[[File:IMG_2401.JPG|600px]]
[[File:IMG_2401.JPG|600px]]
[[File:IMG_2410.JPG|600px]]
[[File:IMG_2410.JPG|600px]]
The zynaptik board has some extra circuitry which doesn't have anything soldered on it. These are used for modifying the board, and it is fully functional as it is.
The zynaptik board has some extra circuitry which doesn't have anything soldered on it. These are used for adding extra functionality to the board.
===Mount the Display===
===Mount the Display===
4. After 5-10 seconds, the zynthian UI will be shown
4. After 5-10 seconds, the zynthian UI will be shown
If you get the Zynthian UI, then you have assembled the Zynthian box correctly.
If you get the Zynthian UI, then you have assembled the Zynthian box correctly. Congratulations!
[[file:IMG_2490.JPG|600px]]
[[file:IMG_2490.JPG|600px]]
The selector must go down when rotating clockwise and go up when rotating counter-clockwise. If the rotation sense is reversed, you should check the wiring. Perhaps one of the connections are faulty. The wires' color sequence should be red, black, yellow, green.
The selector must go down when rotating clockwise and go up when rotating counter-clockwise. If the rotation sense is reversed, you should check the wiring. Perhaps one of the connections are faulty. The wires' color sequence should be red, black, yellow, green.
4. Select the ZynAddSubFX engine, select channel #1, select 'Collection' and preset 'Metal Drips' present.
4. Select the ZynAddSubFX engine, select channel #1, select bank 'Collection' and preset 'Metal Drips'.
[[File:IMG_2497.JPG|600px]]
[[File:IMG_2497.JPG|600px]]
If one of the controllers doesn't work correctly, check the wiring again.
If one of the controllers doesn't work correctly, check the wiring again.
6. Push SELECT to move to the next controller screen. Bold push (a push lasting a few seconds) to select a controller screen from the list.
6. Push SELECT to move to the next controller screen. Bold push (a push lasting about 1 second) to select a controller screen from the list.
7. Push BACK. You should go back to the 'Preset Selection' screen.
7. Push BACK. You should go back to the 'Preset Selection' screen.