Line 115: |
Line 115: |
| | | |
| https://discourse.zynthian.org | | https://discourse.zynthian.org |
| + | |
| + | {{WarningBox|Please, handle electronic parts with care, specially the display, as it's easy to damage.}} |
| | | |
| ===Secure the Jack connectors=== | | ===Secure the Jack connectors=== |
Line 145: |
Line 147: |
| | | |
| [[File:IMG2406.JPG|600px]] | | [[File:IMG2406.JPG|600px]] |
| + | |
| + | {{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short jumpers JP1 & JP2 in the zynaptik board.}} |
| | | |
| ===Assemble the Main Computing Block=== | | ===Assemble the Main Computing Block=== |
Line 184: |
Line 188: |
| | | |
| ===Secure the Display=== | | ===Secure the Display=== |
| + | |
| + | {{WarningBox|Please, handle electronic parts with care, specially the display, as it's easy to damage.}} |
| | | |
| For fixing the display to the case cover, you have to use this set: | | For fixing the display to the case cover, you have to use this set: |
Line 189: |
Line 195: |
| [[File:IMG_1295.JPG|400px]] | | [[File:IMG_1295.JPG|400px]] |
| | | |
− | It's composed of 4 bolts, 4 nuts and 4 nylon separators. Before fixing the screen, don't forget to remove the protective plastic sheet. | + | It's composed of 4 bolts, 4 nuts and 4 nylon separators. Before securing the screen, don't forget to remove the protective plastic sheet. For tightening the bolts you could use a 2mm Allen key while hold the nut with your fingers. |
| | | |
| [[File:IMG_2423.JPG|600px]] | | [[File:IMG_2423.JPG|600px]] |
Line 199: |
Line 205: |
| [[File:Rotary&wire.JPG|600px]] | | [[File:Rotary&wire.JPG|600px]] |
| | | |
− | Fix the 4 controller modules to the case cover using the 4 bolts and washers attached to every rotary encoder. | + | Fix the 4 controller modules to the case cover using the 4 nuts and washers attached to every rotary encoder. |
| | | |
| [[File:ZynScreen&Controller.JPG|600px]] | | [[File:ZynScreen&Controller.JPG|600px]] |
Line 234: |
Line 240: |
| | | |
| [[File:MIDIConnector.JPG|600px]] | | [[File:MIDIConnector.JPG|600px]] |
| + | |
| + | {{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short jumpers JP1 & JP2 in the zynaptik board.}} |
| | | |
| | | |
Line 243: |
Line 251: |
| | | |
| The black wire on the "R" pin, white on the "L" one and red on "GND" (middle). | | The black wire on the "R" pin, white on the "L" one and red on "GND" (middle). |
| + | |
| + | {{NoteBox|Some kits have flipped the red and white wires. This is not a problem. Simply look at the black wire.}} |
| | | |
| | | |
Line 252: |
Line 262: |
| | | |
| The black wire should be connected to pin 3, red wire to pin 2 and white wire to pin 1. Looking at the first photo, numbering is left to right. | | The black wire should be connected to pin 3, red wire to pin 2 and white wire to pin 1. Looking at the first photo, numbering is left to right. |
| + | |
| + | {{NoteBox|Some kits have flipped the red and white wires. This is not a problem. Simply look at the black wire.}} |
| | | |
| ===Connect the Display=== | | ===Connect the Display=== |