2,705
edits
Changes
Jump to navigation
Jump to search
Line 6:
Line 6: − + Line 99:
Line 99: + + + + + Line 110:
Line 115: + + Line 140:
Line 147: + + Line 179:
Line 188: + + Line 184:
Line 195: − + Line 194:
Line 205: − + Line 229:
Line 240: + + Line 238:
Line 251: + + Line 247:
Line 262: + + Line 259:
Line 276: + + + + + Line 422:
Line 444: − + − + − I recommend you disconnect the controller and 2in1 modules and try to boot again.+ − − + − In that case, probably the system is not booting correctly. You could try to connect a HDMI display and see if the system is booting. If you can't see the booting sequence, then you should re-burn your SD-card with the Zynthian image. Also, check that your image file is correct by using the SHA1 signature.+ + + − '''More coming soon ...'''+ Line 447:
Line 470: − You can find all this info and much more in the project's [https://github.com/zynthian/zynthian-hw Hardware Repository].+ − ===Electrical Schematic===+ − This is the electrical scheme of the All-In-One circuit:+ − + − − ===RBPi GPIO=== − − [[File:Raspberry-Pi-j8header-2b.png|400px]]
Building a Zynthian Box using an official Kit v3 (view source)
Revision as of 00:25, 2 November 2019
, 00:25, 2 November 2019→Mount the MIDI activity LEDS
[http://shop.zynthian.org Zynthian Shop]
[http://shop.zynthian.org Zynthian Shop]
Specifically, the instructions are for the assembly of kits v3 (version 3), those using the Zynaptik circuit and the ZynScreen v1.4 display.
Specifically, these instructions are for assembling kit v3 (version 3), those kits using the Zynaptik circuit and the ZynScreen v1.4 display.
[[File:IMG_2379.JPG|600px]]
[[File:IMG_2379.JPG|600px]]
[[File:IMG_2384.JPG|600px]]
[[File:IMG_2384.JPG|600px]]
==== Unboxing the Official Kit V3, by Sébastien Marty ====
<embedvideo service="youtube">https://www.youtube.com/watch?v=dFTSyUoUUTQ</embedvideo>
=Assembling your Zynthian Box=
=Assembling your Zynthian Box=
https://discourse.zynthian.org
https://discourse.zynthian.org
{{WarningBox|Please, handle electronic parts with care, specially the display, as it's easy to damage.}}
===Secure the Jack connectors===
===Secure the Jack connectors===
[[File:IMG2406.JPG|600px]]
[[File:IMG2406.JPG|600px]]
{{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short jumpers JP1 & JP2 in the zynaptik board.}}
===Assemble the Main Computing Block===
===Assemble the Main Computing Block===
===Secure the Display===
===Secure the Display===
{{WarningBox|Please, handle electronic parts with care, specially the display, as it's easy to damage.}}
For fixing the display to the case cover, you have to use this set:
For fixing the display to the case cover, you have to use this set:
[[File:IMG_1295.JPG|400px]]
[[File:IMG_1295.JPG|400px]]
It's composed of 4 bolts, 4 nuts and 4 nylon separators. Before fixing the screen, don't forget to remove the protective plastic sheet.
It's composed of 4 bolts, 4 nuts and 4 nylon separators. Before securing the screen, don't forget to remove the protective plastic sheet. For tightening the bolts you could use a 2mm Allen key while hold the nut with your fingers.
[[File:IMG_2423.JPG|600px]]
[[File:IMG_2423.JPG|600px]]
[[File:Rotary&wire.JPG|600px]]
[[File:Rotary&wire.JPG|600px]]
Fix the 4 controller modules to the case cover using the 4 bolts and washers attached to every rotary encoder.
Fix the 4 controller modules to the case cover using the 4 nuts and washers attached to every rotary encoder.
[[File:ZynScreen&Controller.JPG|600px]]
[[File:ZynScreen&Controller.JPG|600px]]
[[File:MIDIConnector.JPG|600px]]
[[File:MIDIConnector.JPG|600px]]
{{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short jumpers JP1 & JP2 in the zynaptik board.}}
The black wire on the "R" pin, white on the "L" one and red on "GND" (middle).
The black wire on the "R" pin, white on the "L" one and red on "GND" (middle).
{{NoteBox|Some kits have flipped the red and white wires. This is not a problem. Simply look at the black wire.}}
The black wire should be connected to pin 3, red wire to pin 2 and white wire to pin 1. Looking at the first photo, numbering is left to right.
The black wire should be connected to pin 3, red wire to pin 2 and white wire to pin 1. Looking at the first photo, numbering is left to right.
{{NoteBox|Some kits have flipped the red and white wires. This is not a problem. Simply look at the black wire.}}
===Connect the Display===
===Connect the Display===
[[File:Precierre.JPG|600px]]
[[File:Precierre.JPG|600px]]
=== Building and Testing the Official Kit V3, by Sébastien Marty ===
<embedvideo service="youtube">https://www.youtube.com/watch?v=e5gpAZL8kiE</embedvideo>
=Testing your Zynthian Box=
=Testing your Zynthian Box=
In this section i will try to give you some tips for locating and solving the problems you may have.
In this section i will try to give you some tips for locating and solving the problems you may have.
For finding and solving problems, i really recommend to connect a HDMI display to the RBPi. It will give you accurate information during the booting sequence. Also, if you connect a USB keyboard, you can login into the system and get extra information, inspect the logs, etc.
For finding and solving problems, i really recommend to connect a HDMI display to the RBPi. It will give you accurate information during the booting sequence. Also, if you connect an USB keyboard, you could login into the system and get extra information, inspect the logs, etc.
===The display don't go white in the boot stage 1===
===The display don't show the zynthian splash screen on boot===
In that case, probably the system is not booting correctly. You could try to connect a HDMI display and see if the system is booting. If you can't see the booting sequence, then you should re-burn your SD-card with the Zynthian image. Also, check that your image file is correct by using the SHA1 signature.
If the problem persist it's very probable you haven't solder correctly the side 26-pin connector. You should double check the connector and be sure that it's correctly soldered.
===The display don't show the zynthian splash screen in the boot stage 2===
===You get the zynthian error screen with the IP===
Your hardware seems to be incorrectly configured. You should access the webconf tool and configure your hardware.
===Your controllers doesn't work===
You make a mistake while connecting the controllers or your hardware (wiring layout) is incorrectly configured. You should access the webconf tool and configure your hardware.
===You can't solve the problem===
===You can't solve the problem===
Finally, i have included here some detailed schemes. People hacking the standard Zynthian design would find it very useful. Also, if you have some problem and need to "debug", you would find it useful too.
Finally, i have included here some detailed schemes. People hacking the standard Zynthian design would find it very useful. Also, if you have some problem and need to "debug", you would find it useful too.
[[File:Zynthian_controller_single2_smd.svg|600px]]
[[File:Zynthian_zynaptik.svg|600px]]
[[File:ZynScreen_v1.3.svg|600px]]
[[File:Zynthian_allinone.sch.svg|800px]]
You can find all this info and much more in the project's [https://github.com/zynthian/zynthian-hw Hardware Repository].