2,705
edits
Changes
Jump to navigation
Jump to search
Line 298:
Line 298: − + − + − + − [[File:IMG_1563.JPG|600px]]+ − If it doesn't works, try pushing the 'snapshot' controller. Perhaps you have cross-wired the 3 & 4 controllers and in that case, you have to fix the wiring. If it doesn't work, try pushing the other two controllers and rotating the controllers. If something happens, most probably you have reversed the wiring order when connecting the controllers. Double-check the wiring again.+ − 2. Rotate the 'SELECT' controller to select the engine you want to start for the new layer. + − The selector must go down when rotating clockwise and go up when rotating counterclockwise. If the rotation sense is reversed, you should check the wiring.+ − 3. Select the ZynAddSubFX engine, select channel #1, bank and preset. You should get into the 'Instrument Control' screen.+ − [[File:IMG_1568.JPG|600px]]+ − 4. Rotate every control to test that it works and that the rotation sense is correct. + − If some controller doesn't work correctly, check the wiring again. You could try to figure what is happening by analizing the observed behaviour.+ − 5. Push 'BACK'. You should go back to the 'Preset Selection' screen. + − 6. Push 'Layer' again to return to the 'Layer Selection' screen. Try to create another layer following the same procedure. + − [[File:IMG_1584.JPG|600px]]+ − 7. From the "Instrument Control" screen, push 'Snapshot' to get into the 'Load Snapshot' screen. Push 'Snapshot' again to 'Save Snapshot'. Push 'BACK' to return to the 'Instrument Control' screen. + − + + + + + + + + + + + + + + + + + + + + + Line 376:
Line 396: + + − + + Line 387:
Line 410: − + − + − + − - '''restart GUI''' (or '''reboot''') from the admin menu + + Line 398:
Line 422: − + + + − ===The display don't go white in the boot stage 1===+ − I recommend you disconnect the controller and 2in1 modules and try to boot again.+ − If the problem persist it's very probable you haven't solder correctly the side 26-pin connector. You should double check the connector and be sure that it's correctly soldered. − ===The display don't show the zynthian splash screen in the boot stage 2===+ − In that case, probably the system is not booting correctly. You could try to connect a HDMI display and see if the system is booting. If you can't see the booting sequence, then you should re-burn your SD-card with the Zynthian image. Also, check that your image file is correct by using the SHA1 signature.+ − '''More coming soon ...'''+ Line 424:
Line 449: − − ===Electrical Schematic=== − − This is the electrical scheme of the All-In-One circuit: − − [[File:Zynthian_allinone.sch.svg|800px]] − − ===RBPi GPIO=== − − [[File:Raspberry-Pi-j8header-2b.png|400px]]
Building a Zynthian Box using an official Kit v3 (view source)
Revision as of 20:37, 17 July 2019
, 20:37, 17 July 2019no edit summary
* Save the changes and reboot your Zynthian.
* Save the changes and reboot your Zynthian.
===Test the Controllers===
===Test the Controllers & UI===
If you get into the Zynthian UI, then you should be in the 'Layer Selection' screen. Let's start testing that your controllers are working OK.
If you get into the Zynthian UI, then you should be in the 'Layer list' screen. Let's start testing that your controllers are working OK.
1. Push 'select' to create a new layer. You should get into the 'Engine Selection' screen.
1. Rotate the SELECT controller up & down for selecting the different options in the Layers menu.
2. Push SELECT to create a New 'Synth Layer'. You should get into the 'Engine Selection' screen.
[[File:IMG_2496.JPG|600px]]
If it doesn't works, try rotating/pushing the 'learn/snapshot' controller. Perhaps you have cross-wired the 3 & 4 controllers and in that case, you have to fix the wiring. If it doesn't work, try pushing the other two controllers and rotating the controllers. If something happens, most probably you have reversed the wiring order when connecting the controllers. Double-check the wiring again.
3. Rotate the SELECT controller to choose the engine you want to instance for the new layer.
The selector must go down when rotating clockwise and go up when rotating counter-clockwise. If the rotation sense is reversed, you should check the wiring. Perhaps some harness is faulty. The wires color sequence should be: red, black, yellow, green.
4. Select the ZynAddSubFX engine, select channel #1, bank 'Collection' and preset 'Metal Drips'.
[[File:IMG_2497.JPG|600px]]
You should get into the 'Instrument Control' screen.
[[File:IMG_2500.JPG|600px]]
5. Rotate every control to test that it works and that the rotation sense is correct.
If some controller doesn't work correctly, check the wiring again. You could try to figure what is happening by analyzing the observed behaviour.
6. Push SELECT to move to the next controller screen. Bold push to select a controller screen from the list.
If everything is working OK, then you should read the [[Zynthian_Users_Guide|User's Guide]] and start enjoying your Zynthian Box, but before that ...
7. Push BACK. You should go back to the 'Preset Selection' screen.
[[File:IMG_2499.JPG|600px]]
8. Push BACK again. You should go back to the 'Bank Selection' screen.
[[File:IMG_2498.JPG|600px]]
9. Push LAYER again to return to the 'Layer Selection' screen. Try to create another layer following the same procedure.
[[File:IMG_2509.JPG|600px]]
10. Push 'SNAPSHOT' to get into the 'Snapshot' screen. Select 'New Snapshot' and your first snapshot will be stored.
[[File:IMG_2506.JPG|600px]]
If everything is working OK, then you should read the [[Zynthian_Users_Guide|User's Guide]] and start enjoying your Zynthian Box, but before that ... why not enjoying a little bit? Connect your MIDI keyboard, your speakers and check this out:
Bank 'net-wisdom', Preset 'Vangelis Saw - C'
Keep pushing a single note (or a chord) and move the cutoff and resonance controllers. Enjoy! ;-)
===Test the Audio Output===
===Test the Audio Output===
Take your time to see how to bend and drive the cables to get a good fitting when closing the case. The ribbon bus cable is pre-bended for easing this process.
Take your time to see how to bend and drive the cables to get a good fitting when closing the case. The ribbon bus cable is pre-bended for easing this process.
[[File:Precierre.JPG|600px]]
[[File:Precierre.JPG|600px]]
Finally, screw-drive the 8 sheet-threader bolts for securing the case, 4 each side.
Finally, screw-drive the 8 sheet-threader bolts for securing the case, 4 each side.
[[File:IMG_2287.JPG|600px]]
[[File:ZynthianFront.jpg|600px]]
=Update your Zynthian Box=
=Update your Zynthian Box=
If you are using the official Zynthian SD Image, the first thing you should do after booting up your Zynthian Box and having the controllers working OK is update the software:
If you are using the official Zynthian SD Image, the first thing you should do after booting up your Zynthian Box and having the controllers working OK is update the software:
- connect the Zynthian Box to your router using a RJ45 cable
- connect your Zynthian Box to your router using an ethernet cable
- '''update zynthian software''' from the admin menu
- from the admin menu, click '''update software'''
- '''update zynthian library''' from the admin menu
- from the admin menu, click '''restart UI''' (or '''reboot''')
The update process can take some time. Be patient. If you get some ERROR message while updating, please, [https://discourse.zynthian.org/t/problems-updating-the-software-from-the-admin-menu/386 ask in the forum]. You can send a photo or description of the error message.
The update process can take some time. Be patient. If you get some ERROR message while updating, please, [https://discourse.zynthian.org/t/problems-updating-the-software-from-the-admin-menu/386 ask in the forum]. You can send a photo or description of the error message.
You can also update the software using the webconf tool, or from the command line.
=Locating and Solving problems=
=Locating and Solving problems=
In this section i will try to give you some tips for locating and solving the problems you may have.
In this section i will try to give you some tips for locating and solving the problems you may have.
For finding and solving problems, i really recommend to connect a HDMI display to the RBPi. It will give you accurate information during the booting sequence. Also, if you connect a USB keyboard, you can login into the system and get extra information, inspect the logs, etc.
For finding and solving problems, i really recommend to connect a HDMI display to the RBPi. It will give you accurate information during the booting sequence. Also, if you connect an USB keyboard, you could login into the system and get extra information, inspect the logs, etc.
===The display don't show the zynthian splash screen on boot===
In that case, probably the system is not booting correctly. You could try to connect a HDMI display and see if the system is booting. If you can't see the booting sequence, then you should re-burn your SD-card with the Zynthian image. Also, check that your image file is correct by using the SHA1 signature.
===You get the zynthian error screen with the IP===
Your hardware seems to be incorrectly configured. You should access the webconf tool and configure your hardware.
===Your controllers doesn't work===
You make a mistake while connecting the controllers or your hardware (wiring layout) is incorrectly configured. You should access the webconf tool and configure your hardware.
===You can't solve the problem===
===You can't solve the problem===
You can find all this info and much more in the project's [https://github.com/zynthian/zynthian-hw Hardware Repository].
You can find all this info and much more in the project's [https://github.com/zynthian/zynthian-hw Hardware Repository].