Build a Zynthian

1 How to build a Zynthian (Prototype-3)

Manual is currently in development! (20150406)

1.1 Prerequireries

Want to join the Zynthian community? No problem! Build your own one is not very difficult.

1.1.1 Needed competences

For building the hardware you should have the following competences:

• Soldering
• Not to be afraid working with electronic hardware and parts
• Basic understandment of reading electronic circuit diagrams

1.1.2 Tools

• Screw drivers
• Soldering iron
• Tin-solder
• Side cutter

1.2 Hardware

1.2.1 Bill of Material

Here is a list of hardware you need. I have noticed also where I bought the hardware and the price. This items are bought in February 2016 in Germany, so all descriptions are in german and prices are in EUR. If you live in other countries there maybe are better sources of supply for you in your home country.

No	Shipper	Order no.	Description	Pieces	Price per piece [€]
1	http://www.reichelt.de	1N 4148	Planar Epitaxial Schaltdiode, DO35, 100V, 0,15A	1	0,04
2	http://www.reichelt.de	6N 138	OPTOKOPPLER	1	0,58
3	http://www.reichelt.de	RASPBERRY PI 2	Raspberry Pi 2, 4x 900 MHz, 1 GB RAM	1	37,50
4	http://www.reichelt.de	RPI HB DAC+ RCA	HiFiBerry DAC+ RCA, Raspberry Pi Shield	1	35,90
5	http://www.reichelt.de	1/4W 220	Kohleschichtwiderstand 1/4W, 5%, 220 Ohm	1	0,10
6	http://www.reichelt.de	1/4W 1,0K	Kohleschichtwiderstand 1/4W, 5%, 1,0 K-Ohm	1	0,10
7	http://www.reichelt.de	1/4W 10K	Kohleschichtwiderstand 1/4W, 5%, 10 K-Ohm	1	0,10
8	http://www.reichelt.de	MKS-02 100N	WIMA Folienkondensator, Rm 2,5mm 100nF	4	0,15
9	http://www.reichelt.de	GS 18P	IC-Sockel, 18-polig, superflach, gedreht, vergold.	1	0,32
10	http://www.reichelt.de	GS 8P	IC-Sockel, 8-polig, superflach, gedreht, vergold.	1	0,19
11	http://www.reichelt.de	SL 2X25G 2,54	2x25pol.-Stiftleiste, gerade, RM 2,54	1	0,24
12	http://www.reichelt.de	MAB 5S	DIN-Buchse, 5-polig	1	0,24
13 (OPTIONAL)	http://www.reichelt.de	NTA 176	6,3 Mono-Klinken-Bu. auf Cinch-St.	2	0,35
14	http://www.reichelt.de	NT MUSB 2 SW	Micro-USB Steckernetzteil, schwarz, 5 V, 2 A	1	8,40
15	http://www.segor.de	MCP23008-E/P	MCP23008 8 port I2C-GPIO extender	1	2,10
16	http://www.amazon.de	Adafruit PiTFT 2.8"	Adafruit PiTFT Touchscreen Display, 2,8 Zoll, für Raspberry Pi Computer	1	32,00
17	http://www.ebay.de	12mm Rotary Encoder Switch	Rotary Encoder with switch, 20 steps	4	0,60
18	http://www.ebay.de	Poti knob	Poti knob for Rotary encoder (Pos. 17)	4	1,50
19	http://blog.zynthian.org	Encoder PCB	PCB for encoders	2	10,00
20	http://blog.zynthian.org	2in1 PCB	PCB for MIDI and GPIO extension	1	10,00
21	http://blog.zynthian.org	Main Bus Ribbon Cable	Raspberry Main Bus Ribbon Cable	1	20,00
22	http://blog.zynthian.org	Mini-ribbon cable	Mini-ribbon cable (6 pin female connector to 6 female jumper connectors	3	3,00
23	http://www.saturn.de	SD card	Samsung 32GB SD card	1	14,00
24	-	Short connector cables	Connector cables pin-female/pin-female for MIDI and external GPIO connector from 2in1 board	4	??,??
25	-	Multi-pin connector	1x40pol.-Stiftleiste, gerade, RM 2,54	1	??,??

Notes:

• Pos. 19-22 are directly ordered from Zynthian.
• There is no case in this BoM - You have to build your own.
• Sum of all is: 200,27 € (plus shipping)

1.3 Implement and soldering of the PCBs

1.3.1 Step 1: 2in1 board

1.3.1.1 You need:

• 1 * 2in1 PCB (Pos. 20)
• 2 * 100nF capacitor (Pos. 8)
• 1 * multi-pin 2 pins wide (part of Pos. 24)
• 1 * multi-pin 6 pins wide (part of Pos. 24)
• 1 * multi-pin 8 pins wide (part of Pos. 24)
• 1 * resistor 10 kOhm (brown-black-orange-gold, Pos. 7)
• 1 * resistor 1 kOhm (brown-black-red-gold, Pos. 6)
• 1 * resistor 220 Ohm (red-red-black-gold, Pos. 5)
• 1 * diode 1N4148 (Pos. 1)
• 1 * IC socket 8 pins (Pos. 10)
• 1 * IC socket 18 pins (Pos. 9)
• 1 * IC 6N138 (Pos. 2)
• 1 * IC MCP23008 (Pos. 15)
• 2 * Connector cable pin-female/pin-female
• 1 * MIDI socket (DIN socket 5pins)
• 1 * 2in1 PCB (Pos. 20)

1.3.1.2 HowTo:

1. Start with assembling the diode onto the PCB. Be careful to do this the right way - the small black (or white) stripe on one side of the diode must fit the same side of the white stripe on the PCB!
2. After that solder the resistors.
3. Then assemble the IC sockets, but do not put the ICs inside. We will do this at the end of this task.
4. After that, solder the capacitors and the multi-pin-rows.
5. Now insert the ICs into the socket. Be careful to put them weith the notch on the IC towards the hole of the white rectangle showing on the PCB!

1. For the MIDI socket you have to cut of one side of the female/female pin-connector and solder it on the DIN-socket. Connect them to pin 5 (2nd from left) and pin 4 (2nd from right).

1.3.2 Step 2: Encoder boards

1.3.2.1 You need (for one Encoder PCB:

• 2 * Rotary Encoder with switch (Pos. 17)
• 2 * 100nF capacitor (Pos. 8)
• 1 * multi-pin 6 pins wide (part of Pos. 24)
• 1 * Encoder PCB (Pos. 19)

1.3.2.2 HowTo:

1. The order of the following steps is not important: Solder the capacitors, the 6-pin-row and the Encoders on the board - that's it.
2. You have to do this twice - you need two encoder boards.

1.3.3 Step 3: Pin row on the Hifiberry

1.3.3.1 You need:

• 1 * HiFiBerry DAC+ RCA, Raspberry Pi Shield (Pos. 4)
• 1 * 2x25pol.-Stiftleiste, gerade, RM 2,54 (Pos. 11)

1.3.3.2 HowTo:

1. For this part you should have some time. It will be very worse when damaging the Hifiberry!
2. First of all: cut the 2*25 pin-row to 2*20 pin (perhaps with a cutter).
3. Place the pin-row on the Hifiberry and start to solder on the back of the Hifiberry. I used to solder pins which are not next together to avoid hot spots. You also can pause some time for cooling down the area you soldered last.