Line 92: |
Line 92: |
| + '''1 x Zynductor''' | | + '''1 x Zynductor''' |
| | | |
− | [[File:Rbpi4 shop.jpg|330px]][[File:HifiBerryDACADC-Stage-top.jpg|330px]][[File:IMG_2775_OK_shop.JPG|330px]][[File:Controllers_shop.jpeg|330px]][[File:Zynaptik shop.jpeg|330px]][[File:Ribbon_shop.jpeg|330px]][[File:Zynthian_alucase_v41-persp.jpg|330px]][[File:IMG_2887_OK_1024.JPG|400px]][[File:IMG_2887_OK_1024.JPG|400px]][[File:Boltsnuts.JPG|440px]][[File:IMG_2756_OK_shop.JPG|220px]] | + | [[File:Rbpi4 shop.jpg|330px]][[File:HifiBerryDACADC-Stage-top.jpg|330px]][[File:IMG_2775_OK_shop.JPG|330px]][[File:Controllers_shop.jpeg|330px]][[File:Zynaptik shop.jpeg|330px]][[File:Ribbon_shop.jpeg|330px]][[File:Zynthian_alucase_v41-persp.jpg|330px]][[File:ZynAuCon miniribbon.jpg|400px]][[File:IMG_2887_OK_1024.JPG|400px]][[File:Boltsnuts.JPG|440px]][[File:IMG_2756_OK_shop.JPG|220px]] |
| | | |
| ===Unboxing the Zynthian Kit v4=== | | ===Unboxing the Zynthian Kit v4=== |
Line 117: |
Line 117: |
| The ZynAuCon module improves and simplifies the audio wiring by using a small ribbon cable for driving the 4 balanced channels (2 inputs + 2 outputs) to the 4 high-quality Neutrik TSR case-connectors. For mounting the ZynAuCon, secure the 2 x 15mm separators with 2 x black-anodized bolts M2.5. Next, you have to insert the board from inside the case and secure them with the 4 x nuts from the outside. Use a wrench for tightening the nuts, but not too much, and take care of not damaging the surface of the nice aluminum case!! | | The ZynAuCon module improves and simplifies the audio wiring by using a small ribbon cable for driving the 4 balanced channels (2 inputs + 2 outputs) to the 4 high-quality Neutrik TSR case-connectors. For mounting the ZynAuCon, secure the 2 x 15mm separators with 2 x black-anodized bolts M2.5. Next, you have to insert the board from inside the case and secure them with the 4 x nuts from the outside. Use a wrench for tightening the nuts, but not too much, and take care of not damaging the surface of the nice aluminum case!! |
| | | |
− | [[File:IMG_2886_OK_1024.JPG|400px]] | + | [[File:IMG_3419_fixed.JPG|200px]] |
− | [[File:IMG_2896_OK_1024_fixv41.JPG|400px]] | + | [[File:IMG_3355_fixed.JPG|400px]] |
− | [[File:IMG_2898_OK_1024.JPG|400px]] | + | [[File:IMG_3387_fixed.JPG|400px]] |
| + | |
| + | [[File:IMG_3395_fixed.JPG|400px]] |
| + | [[File:IMG_3401_fixed2.JPG|500px]] |
| | | |
| ===Secure the MIDI connectors=== | | ===Secure the MIDI connectors=== |
Line 291: |
Line 294: |
| Plug the little 2x10 ribbon cable on the Hifiberry's J1 connector. Next, plug the other end on the ZynAuCon board. Observe that the ribbon cable must be bent forming a 90º angle, so it fits perfectly the space and distance between the 2 IDC connectors. | | Plug the little 2x10 ribbon cable on the Hifiberry's J1 connector. Next, plug the other end on the ZynAuCon board. Observe that the ribbon cable must be bent forming a 90º angle, so it fits perfectly the space and distance between the 2 IDC connectors. |
| | | |
− | [[File:HifiBerryDACADC-Stage-connection-OUT.png|600px]] | + | |
| + | [[File:IMG_3410_fixed.JPG|600px]] |
| + | |
| | | |
| FYI, this is the specification for the 10-pin header (J1) on the Hifiberry DAC+ADC Stage: | | FYI, this is the specification for the 10-pin header (J1) on the Hifiberry DAC+ADC Stage: |