334
edits
Changes
Jump to navigation
Jump to search
mLine 28:
Line 28: − + Line 84:
Line 84: − + − + Line 93:
Line 93: − + − + Line 367:
Line 367: − +
Building a Zynthian Box using official Kits v4.2-v4.6 (view source)
Revision as of 07:39, 20 May 2022
, 07:39, 20 May 2022Fix typo
** [https://shop.zynthian.org/shop/product/zynthian-ribbon-bus-cable-278?category=16 Ribbon bus cable]
** [https://shop.zynthian.org/shop/product/zynthian-ribbon-bus-cable-278?category=16 Ribbon bus cable]
** [https://shop.zynthian.org/shop/product/raspberry-pi-15-3w-usb-c-power-supply-389?category=16 Power supply for RBPi 4] (5V 3A USB type-C connector) => Optional
** [https://shop.zynthian.org/shop/product/raspberry-pi-15-3w-usb-c-power-supply-389?category=16 Power supply for RBPi 4] (5V 3A USB type-C connector) => Optional
** 16GB micro-SD card or bigger (Use a high-quality card) => '''Needed but not included''' on official kits!
** micro-SD card >16GB (use a good-quality card) => '''Needed but not included''' on official kits!
=Some definitions=
=Some definitions=
===Zynthian Kit v4===
===Zynthian Kit v4===
A Zynthian Kit is a set of electronic and mechanic parts. The ''official'' Zynthian Kit v4.2 consists of these parts:
A Zynthian Kit is a set of electronic and mechanic parts. The ''official'' Zynthian Kit v4.6 consists of these parts:
+ '''1 x Raspberry Pi 4'''
+ '''1 x Raspberry Pi 4'''
+ '''1 x Hifiberry DAC+ADC PRO'''
+ '''1 x ZynADAC Soundcard'''
+ '''1 x ZynAuCon Module + Mini-ribbon cable'''
+ '''1 x ZynAuCon Module + Mini-ribbon cable'''
+ '''1 x ZynScreen v1.5:''' Touch-Display 3.5" + Controllers circuit + Silicone buttons
+ '''1 x ZynScreen v1.5:''' Touch-Display 3.5" + Controllers circuit + Silicone buttons
+ '''1 x Zynaptik Module:''' MIDI Ports + extended I/O
+ '''1 x Zynaptik Module:''' MIDI Ports + extended I/O
+ '''1 x Ribbon bus cable'''
+ '''1 x Ribbon bus cable'''
+ '''1 x Zynthian Aluminium Case'''
+ '''1 x Aluminium Case'''
+ '''1 x MIDI Connectors Set + LEDs'''
+ '''3 x MIDI Connectors with harness + LEDs'''
+ '''1 x Bolts & Nuts Set'''
+ '''1 x Bolts & Nuts Set'''
+ '''1 x Zynductor'''
+ '''1 x Zynductor'''
[[file:IMG_2490.JPG|600px]]
[[file:IMG_2490.JPG|600px]]
If you don't get an error screen or a blank screen, you probably you made a mistake during the assembly. You have to [[#Locating_and_Solving_problems|locate and solve the problem(s)]].
If you get an error screen or a blank screen, you probably made a mistake during the assembly. You will have to [[#Locating_and_Solving_problems|locate and solve the problem(s)]].
If you are using the Aruk RC-3 SD image (which you should), you will notice that the controllers are not working at all. This SD image is pre-configured for working with the kit v2, so you need to configure the software for working with the kit v3. The simplest way of doing it is using the webconf tool:
If you are using the Aruk RC-3 SD image (which you should), you will notice that the controllers are not working at all. This SD image is pre-configured for working with the kit v2, so you need to configure the software for working with the kit v3. The simplest way of doing it is using the webconf tool: