Line 6: |
Line 6: |
| [http://shop.zynthian.org Zynthian Shop] | | [http://shop.zynthian.org Zynthian Shop] |
| | | |
− | Specifically, these instructions are for assembling Zynthian Kits v4.2, v4.3 & v4.4, that include: | + | Specifically, these instructions are for assembling Zynthian Kits v4.2, v4.3, v4.4 & v4.5, that include: |
| | | |
| * ''Hifiberry DAC+ADC Stage'' or ''ZynADAC'' soundcard | | * ''Hifiberry DAC+ADC Stage'' or ''ZynADAC'' soundcard |
Line 130: |
Line 130: |
| [[File:IMG_3395_fixed.JPG|400px]] | | [[File:IMG_3395_fixed.JPG|400px]] |
| [[File:IMG_3401_fixed2.JPG|500px]] | | [[File:IMG_3401_fixed2.JPG|500px]] |
| + | |
| + | {{NoteBox|In the latest kits (v4.5), the ZynAuCon board includes a mini-jack headphones connector with a volume wheel. Also, the aluminum case has 2 extra holes for securing the ZynAuCon with 2 x M2.5 bolts.}} |
| | | |
| ===Secure the MIDI connectors=== | | ===Secure the MIDI connectors=== |
Line 151: |
Line 153: |
| [[File:IMG_2926_OK_1024.JPG|400px]] | | [[File:IMG_2926_OK_1024.JPG|400px]] |
| | | |
| + | {{WarningBox|Some aluminum cases have the LEDs mounting holes a little bit bigger than it should be. For patching this issue you could use a drop of glue from the inner side.}} |
| | | |
| When it's done, you have to plug the LED wires into the 2 spare "DUPONT" connectors from the MIDI harness (green & yellow wires). Polarity is important, so don't cross the wires: | | When it's done, you have to plug the LED wires into the 2 spare "DUPONT" connectors from the MIDI harness (green & yellow wires). Polarity is important, so don't cross the wires: |
Line 320: |
Line 323: |
| | | |
| '''And that's all!!''' Your Zynthian Box is almost ready to boot. I recommend that you double-check everything before powering up the device. | | '''And that's all!!''' Your Zynthian Box is almost ready to boot. I recommend that you double-check everything before powering up the device. |
| + | |
| + | =Close the case= |
| + | |
| + | Once everything is in its place and you have tested that it works, it's time to close the case |
| + | |
| + | Take your time to bend and push the cables to get a good fit when closing the case. The ribbon bus cable is pre-bent to make this process easier. |
| + | |
| + | |
| + | [[File:IMG_3126_OK_1024.JPG|600px]] |
| + | |
| + | {{WarningBox| If you have a v4.5 kit or higher, you should take extra care for getting the mini-jack headphones connector and the volume wheel to fit into their places. Put special attention to not forcing the volume wheel when opening or closing the case! }} |
| + | |
| + | Finally, fasten the 8 self-taping bolts to secure the case, 4 on each side. |
| + | |
| + | |
| + | [[File:IMG_3148_OK_1024.JPG|800px]] |
| + | |
| + | {{NoteBox| Be careful not to over-tighten the case screws, as it can buckle the top plate. If you notice the top place bowing slightly, loosen the screws a little until the surface is level. }} |
| | | |
| =Testing your Zynthian Box= | | =Testing your Zynthian Box= |
Line 447: |
Line 468: |
| | | |
| If this doesn't work, you have to [[#Locating_and_Solving_problems|locate and solve the problem(s)]]. | | If this doesn't work, you have to [[#Locating_and_Solving_problems|locate and solve the problem(s)]]. |
− |
| |
− | =Final steps=
| |
− |
| |
− | Once everything is in its place and you have tested that it works, it's time to close the case
| |
− |
| |
− |
| |
− | ===Close the case===
| |
− |
| |
− | Take your time to bend and push the cables to get a good fit when closing the case. The ribbon bus cable is pre-bent to make this process easier.
| |
− |
| |
− |
| |
− | [[File:IMG_3126_OK_1024.JPG|600px]]
| |
− |
| |
− |
| |
− | Finally, fasten the 8 sheet-threaded bolts to secure the case, 4 on each side.
| |
− |
| |
− |
| |
− | [[File:IMG_3148_OK_1024.JPG|800px]]
| |
− |
| |
− | {{NoteBox| Be careful not to over-tighten the case screws, as it can buckle the top plate. If you notice the top place bowing slightly, loosen the screws a little until the surface is level. }}
| |
− |
| |
| | | |
| =Update your Zynthian Box= | | =Update your Zynthian Box= |