Line 218: |
Line 218: |
| [[File:IMG_2995_OK_1024.JPG|400px]] | | [[File:IMG_2995_OK_1024.JPG|400px]] |
| [[File:IMG_3011_OK_1024.JPG|400px]] | | [[File:IMG_3011_OK_1024.JPG|400px]] |
| + | |
| + | |
| + | {{NoteBox|Note that your soundcard, the Hifiberry DAC+ADC Stage, has not RCA connectors. Some photos are from an older model, but the mounting instructions doesn't change. }} |
| | | |
| ===Secure the Zynaptik module=== | | ===Secure the Zynaptik module=== |
Line 250: |
Line 253: |
| | | |
| Plug a wire on each controller. Fix the controllers in each corner using the nuts and washers attached to them. | | Plug a wire on each controller. Fix the controllers in each corner using the nuts and washers attached to them. |
− |
| |
− | '''Don't mount the controllers like in the photo''', do it upside-down to avoid pressing the MIDI LED pins. I will update the photo ASAP.
| |
| | | |
| [[File:Rotary&wire.JPG|400px]] | | [[File:Rotary&wire.JPG|400px]] |
Line 297: |
Line 298: |
| | | |
| | | |
− | ===Connect the Audio Output Jack connectors=== | + | ===Connect the TSR Balanced Audio Connectors to the Hifiberry DAC+ADC Stage=== |
− | | |
− | Connect the audio output jack connectors to the audio-output header to the Hifiberry soundcard:
| |
− | | |
− | [[File:dacplus-adc-top audio-out.jpg|350px]]
| |
− | [[File:IMG_2414.JPG|450px]]
| |
− | | |
− | The black wire on the "R" pin, white on the "L" one and red on "GND" (middle).
| |
| | | |
− | {{NoteBox|Some kits have flipped the red and white wires. This is not a problem. Simply look at the black wire.}}
| + | Every TSR connector has 3 colored wires like this: |
| | | |
− | ===Connect the Audio Input Jack connector===
| + | * '''Red''' -> Signal + |
| + | * '''White''' -> Signal - |
| + | * '''Black''' -> Ground |
| | | |
− | This step depends of the specific model of your soundcard:
| + | Each TSR connector must be connected to the 10-pin header (J1) on the Hifiberry DAC+ADC Stage: |
| | | |
− | ====HifiBerry DAC+ADC PRO====
| + | [[File:HifiBerryDACADC-Stage-header.jpg|450px]] |
| | | |
− | Connect the 2 x balanced input jack connectors to the audio-input header on the sound card using the 3x1 pin Dupont connectors as indicated in the image:
| + | First, connect the audio OUT TSR connectors like this: |
| | | |
− | [[File:dacplusadcpro-top-audio-in.jpg|600px]] | + | [[File:HifiBerryDACADC-Stage-connection-OUT.png|600px]] |
| | | |
− | I recommend you take a look at [https://www.hifiberry.com/docs/data-sheets/datasheet-dac-adc-pro Hifiberry DAC+ADC PRO specification].
| + | And then, the audio IN TSR connectors like this: |
| | | |
| + | [[File:HifiBerryDACADC-Stage-connection-IN.png|600px]] |
| | | |
| ===Connect the Display=== | | ===Connect the Display=== |