2,705
edits
Changes
Jump to navigation
Jump to search
Line 118:
Line 118: − + − − Line 131:
Line 129: − + − − Line 144:
Line 140: − + − − Line 155:
Line 149: − + − − Line 171:
Line 163: − − Line 192:
Line 182: − + − Line 204:
Line 193: − + − + − + − − Line 218:
Line 205: − + − − Line 231:
Line 216: − + − − Line 240:
Line 223: − + − + − − Line 256:
Line 237: − [[File:IMG_1295.JPG|400px]] − + + + + + + + Line 264:
Line 250: − + − + − + − − Line 276:
Line 260: − + + Line 286:
Line 271: − + − + + + Line 298:
Line 285: + + + Line 307:
Line 297: − + − + Line 329:
Line 319: + − [[File:Screen&Ribbon.JPG|600px]] − − − At this point, your Zynthian Box should look like this: + + − [[File:Precierre.JPG|600px]] − === Building and Testing the Official Kit V4 ===+ − [In progress] − − And that's all. Your Zynthian Box is almost ready to boot. I recommend that you double-check everything before trying to boot.
Building a Zynthian Box using an official Kit v4.0 (view source)
Revision as of 13:22, 29 July 2020
, 13:22, 29 July 2020→Connect the Audio Output Jack connectors
[[File:IMG_2885_OK_1024.JPG|400px]]
[[File:IMG_2885_OK_1024.JPG|400px]]
[[File:IMG_2890_OK_1024.JPG|400px]]
[[File:IMG_2890_OK_1024.JPG|400px]]
[[File:IMG_2895_OK_1024.JPG|400px]]
[[File:IMG_2895_OK_1024.JPG|800px]]
===Secure the balanced audio input jack-TRS connectors===
===Secure the balanced audio input jack-TRS connectors===
[[File:IMG_2886_OK_1024.JPG|400px]]
[[File:IMG_2886_OK_1024.JPG|400px]]
[[File:IMG_2896_OK_1024.JPG|400px]]
[[File:IMG_2896_OK_1024.JPG|400px]]
[[File:IMG_2898_OK_1024.JPG|400px]]
[[File:IMG_2898_OK_1024.JPG|800px]]
===Secure the MIDI connectors===
===Secure the MIDI connectors===
[[File:IMG_2887_OK_1024.JPG|400px]]
[[File:IMG_2887_OK_1024.JPG|400px]]
[[File:IMG_2903_OK_1024.JPG|400px]]
[[File:IMG_2903_OK_1024.JPG|400px]]
[[File:IMG_2915_OK_1024.JPG|400px]]
[[File:IMG_2915_OK_1024.JPG|800px]]
===Mount the MIDI activity LEDS===
===Mount the MIDI activity LEDS===
[[File:IMG_2888_OK_1024.JPG|400px]]
[[File:IMG_2888_OK_1024.JPG|400px]]
[[File:IMG2403.JPG|400px]]
[[File:IMG2403.JPG|400px]]
[[File:IMG_2926_OK_1024.JPG|400px]]
[[File:IMG_2926_OK_1024.JPG|800px]]
{{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short the JP1 & JP2 jumpers on the zynaptik board.}}
{{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short the JP1 & JP2 jumpers on the zynaptik board.}}
[[File:IMG_2930_OK_1024.JPG|400px]]
[[File:IMG_2930_OK_1024.JPG|400px]]
[[File:IMG_2944_OK_1024.JPG|400px]]
[[File:IMG_2944_OK_1024.JPG|400px]]
===Secure the Main Computing Block and assemble the Zynductor Passive Cooler===
===Secure the Main Computing Block and assemble the Zynductor Passive Cooler===
[[File:IMG_1293.JPG|200px]]
[[File:IMG_1293.JPG|200px]]
[[File:IMG_2952_OK_1024.JPG|300px]]
[[File:IMG_2952_OK_1024.JPG|400px]]
[[File:IMG_2956_OK_1024.JPG|300px]]
[[File:IMG_2956_OK_1024.JPG|400px]]
[[File:IMG_2958_OK_1024.JPG|400px]]
[[File:IMG_2958_OK_1024.JPG|800px]]
[[File:IMG_2966_OK_1024.JPG|400px]]
[[File:IMG_2966_OK_1024.JPG|400px]]
[[File:IMG_2972_OK_1024.JPG|400px]]
[[File:IMG_2972_OK_1024.JPG|400px]]
[[File:IMG_2983_OK_1024.JPG|400px]]
[[File:IMG_2983_OK_1024.JPG|800px]]
[[File:IMG_2992_OK_1024.JPG|400px]]
[[File:IMG_2992_OK_1024.JPG|400px]]
[[File:IMG_2995_OK_1024.JPG|400px]]
[[File:IMG_2995_OK_1024.JPG|400px]]
[[File:IMG_3011_OK_1024.JPG|400px]]
[[File:IMG_3011_OK_1024.JPG|800px]]
===Secure the Zynaptik module===
===Secure the Zynaptik module===
[[File:IMG_1294.JPG|250px]]
[[File:IMG_1294.JPG|250px]]
[[File:Zynaptik_shop.jpeg|550px]]
[[File:Zynaptik_shop.jpeg|400px]]
[[File:IMG_2410.JPG|400px]]
[[File:IMG_2410.JPG|800px]]
The zynaptik board has some extra circuitry which doesn't have anything soldered on it. These are used for adding extra functionality to the board.
The zynaptik board has some extra circuitry which doesn't have anything soldered on it. These are used for adding extra functionality to the board.
===Mount the Display===
===Mount the Display===
The screen is secured with these 4 screws, nuts, and nylon separators. Mount the screen by screwing the screws from the outside and fixing them with the bolts from the inside. The separators go between the screen and the case. Remember to remove the protective film from the screen before mounting it.
The screen is secured with these 4 screws, nuts, and nylon separators. Mount the screen by screwing the screws from the outside and fixing them with the bolts from the inside. The separators go between the screen and the case. Remember to remove the protective film from the screen before mounting it.
[[File:IMG_2423.JPG|600px]]
[[File:IMG_1295.JPG|200px]]
[[File:IMG_3044_OK_1024.JPG|300px]]
[[File:IMG_3049_OK_1024.JPG|300px]]
[[File:IMG_3059_OK_1024.JPG|300px]]
[[File:IMG_3091_OK_1024.JPG|800px]]
===Mount the Controllers===
===Mount the Controllers===
Plug a wire on each controller. Fix the controllers in each corner using the nuts and washers attached to them
Plug a wire on each controller. Fix the controllers in each corner using the nuts and washers attached to them
[[File:Rotary&wire.JPG|600px]]
[[File:Rotary&wire.JPG|400px]]
[[File:ZynScreen&Controller.JPG|400px]]
[[File:ZynScreen&Controller.JPG|600px]]
[[File:IMG_1401.JPG|400px]]
[[File:IMG_1401.JPG|600px]]
===Attach the knobs===
===Attach the knobs===
===Attach the rubber feet===
===Attach the rubber feet===
[[File:IMG 2536.JPG|600px]]
[[File:IMG 2536.JPG|400px]]
=Connecting everything=
=Connecting everything=
The Zynthian Kit 4 is designed to use JST connectors which can't be plugged in wrong, so connecting everything is straight-forward:
The Zynthian Kit 4 is designed to use JST connectors which can't be plugged in wrong, so connecting everything is straight-forward:
===Connect the Ribbon Bus cable===
===Connect the Ribbon Bus cable===
Connect the Main Ribbon Bus cable to the Raspberry Pi's 40-pin header and to the Zynaptik module. The red wire is pin 1, so if you are looking at the case from the front, it should be on the right.
Connect the Main Ribbon Bus cable to the Raspberry Pi's 40-pin header and to the Zynaptik module. The red wire is pin 1, so if you are looking at the case from the front, it should be on the right.
[[File:Ribbon.jpeg|600px]]
[[File:Ribbon&Hifi&Zynaptik.JPG|600px]]
[[File:Ribbon.jpeg|400px]]
[[File:Ribbon&Hifi&Zynaptik.JPG|400px]]
===Connect the Controllers===
===Connect the Controllers===
Connect the 4 controller cables to the 4 controller connectors on the ZynScreen (CTRL1, CTRL2, CTRL3, CTRL4)
Connect the 4 controller cables to the 4 controller connectors on the ZynScreen (CTRL1, CTRL2, CTRL3, CTRL4)
[[File:ZynScreenConnect.JPG|600px]]
[[File:ZynScreenConnect.JPG|600px]]
Connect the 3 cables from the MIDI connectors to the MIDI-IN, MIDI-OUT and MIDI-THRU connectors on the Zynaptik module.
Connect the 3 cables from the MIDI connectors to the MIDI-IN, MIDI-OUT and MIDI-THRU connectors on the Zynaptik module.
[[File:MIDIConnector.JPG|600px]]
[[File:MIDIConnector.JPG|600px]]
{{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short the JP1 & JP2 jumpers on the zynaptik board.}}
{{NoteBox|If you don’t connect the status LEDs, the MIDI-OUT and MIDI-THRU won’t work unless you short the JP1 & JP2 jumpers on the zynaptik board.}}
===Connect the Audio Output Jack connectors===
===Connect the Audio Output Jack connectors===
Connect the audio output jack connectors to the audio-output header to the Hifiberry soundcard:
Connect the audio output jack connectors to the audio-output header to the Hifiberry soundcard:
[[File:dacplus-adc-top audio-out.jpg|600px]]
[[File:dacplus-adc-top audio-out.jpg|350px]]
[[File:IMG_2414.JPG|600px]]
[[File:IMG_2414.JPG|450px]]
The black wire on the "R" pin, white on the "L" one and red on "GND" (middle).
The black wire on the "R" pin, white on the "L" one and red on "GND" (middle).
Connect the ribbon's 26-pin connector to the display's connector. '''Pay attention to the orientation'''. The red wire should be the pin 1, which as marked on the display's PCB surface. Probably you need to remove the red-jumper that is plugged in the connectors pins 1-2, indicating the right position.
Connect the ribbon's 26-pin connector to the display's connector. '''Pay attention to the orientation'''. The red wire should be the pin 1, which as marked on the display's PCB surface. Probably you need to remove the red-jumper that is plugged in the connectors pins 1-2, indicating the right position.
{{WarningBox|Please, double check this step carefully because you could break the display if it's connected reversed!!}}
{{WarningBox|Please, double check this step carefully because you could break the display if it's connected reversed!!}}
[[File:Screen&Ribbon.JPG|500px]]
[[File:Precierre.JPG|400px]]
'''And that's all!!''' Your Zynthian Box is almost ready to boot. I recommend that you double-check everything before powering up the device.
=Testing your Zynthian Box=
=Testing your Zynthian Box=
===Double-check the parts and wiring===
===Double-check the parts and wiring===