1 Previous Requirements

1.1 BOM V5 kit:

Aluminum Case
Main Board
Control Board
Display
Raspberry Pi4
Thermal Block
Silicon Keypad
Wiring
Rubber Feet
Thermal Pad
Screws
Knobs
PSU
SD-Card (NOT included in V5 kit)

1.2 Tools:

Allen Spanner 1.5 mm
Allen Spanner 2.0 mm
Scissors or Cutter (NOT included in V5 kit)
Rule meter (NOT included in V5 kit)

2 General Advice

Read & follow carefully the assembling instructions. Don't ignore any guidance or recommendation. We are quite lazy, so we should had some important reason to write it.

Prepare the mounting space and the needed tools. A clean 120 x 60 cm table will be big enough. More is always welcome. Less is not recommended. Remove all stuff you don't need from the surface and prepare the tools you will need.

Don't use force. Never! Some parts are really delicate, specially flat cable connectors (FPC), and you could easily break something if you are brute. Assembling the V5 unit is not difficult at all, but it's a clock-maker work. A beginners one that almost everyone could do, but clock-maker's task anyway. if you are not very used to manipulate this kind of stuff, please, proceed slowly and think twice to do it once.

Don't be impatient. If you have doubts or you are blocked, please, stop assembling and ask in the forum or send an email to support@zynthian.org. It's better to wait some hours to get an answer than waiting for days/weeks to get a replacement part.

Keep your hands clean so you can enjoy a nice units after finishing.

Again! Please, be extremely delicate when manipulating the flat cable connectors (FPC). They are the weakest parts and can be easily broken. Look carefully the photos/videos and proceed just in the way we recommend. Use 2 hands, one finger from each hand. Avoid manipulating the connectors with a single hand or finger. And don't use any tool for this!!

3 I. BOTTOM PART

3.1 Step 0: Dump the screws bag in a apropiate recipient

Be careful when opening the screws bag. Some of them are really small and you could easily lost some of them. Please, don't dump them on the table's surface or on top a piece of paper. We recommend to dump the bag's content in an small tray, so you can look and take them easily, but getting them well confined so they can't be easily lost.

[photo 0.1] X

4 Step 1: Sticking the rubber feet to the aluminum case bottom=

1. Look for the 4 x rubber feet inside the wiring bag, in the "Screen and Bits" case:

[photo 1.1] X

2. Look for the aluminum case bottom part in the "V5" case:

[photo 1.2] X

3. Stick the 4 x rubber feet to the aluminum case bottom part. This will prevent scratches during the assembling process.

[photo 1.3] X

4.1 Step 2: Fixate the display ribbon cable to the RPi4

1. Look for the display ribbon cable in the "Screen and Bits" case. It's 20cm long and 1.6cm wide:

[photo 2.1] X

2. Look for the RPi4 compute module in the "Accessories" case:

[photo 2.2] X

3. Open the RPi4's DSI connector by pulling softly both sides of the tiny black tongue. When it's totally open, push the ribbon cable inside, leaving the blue side facing out. When you are 100% sure the cable is totally inserted, close the connector by pushing the tongue with 2 fingers, one each hand.

[photo 2.3] X

Note:

When possible, use 2 hands to manipulate the fragile FPC connectors. You will control the applied force a lot better than using a single hand. If you couldn't use 2 hands, extreme your precaution. In fact, extreme your precaution all the time when manipulating FPC connectors.

4.2 Step 3: Fixating the thermal block

Zynthian V5 gets a 25% extra power from the RPi4 by overclocking the CPU up to 2 GHz. For this to work properly, we need to evacuate the heat generated by the RPi4. As we didn't want a fan making noise and pushing dust inside the case, we decided to use the aluminum case as a huge heat-sink. This is achieved by the thermal block, a solid aluminum block that closely contact with the RPi4 chips and serve as a heat-highway to the aluminum case bottom, and from here, to the rest of the aluminum case. When your zynthian is working hard, or when external temperature is high enough, you will note the V5 case is hot. This is good because it means the thermal block is doing its job of transferring heat from inside to the aluminum case body, where it's dissipated to the ambient.

Having understand all this, you may realize this is a key step for getting you V5 working at 100% of its capacity, so don't be in a hurry and take your time for doing a good work. Let's start!

1. Look for a piece of thermal pad in the wiring bag, in the "Screen and Bits" case. It is a piece with an approximate size of 60 x 20 mm, gray on one side and blue on the other.

[photo 3.1] X

2. Cut 4 little pieces of thermal pad with this recommended sizes:

=> 27 x 20 mm => 11 x 11 mm => 11 x 9 mm => 6 x 6 mm

3. You should have received a 60x20 mm piece of thermal pad, so you could proceed by cutting strips like these:

+ 27 x 20 mm + 11 x 20 mm => cut this to get 11x11 & 9x11 mm pieces + 6 x 20 mm => cut this to get the tiny 6x6 mm piece

[photo 3.2] X

4. Remove the blue protective sheet from the 3 smaller pieces and glue them to the inner side of the thermal block, the one that makes contact with the RPi4. You'll recognize it because it has 3 small rectangular islands that fit the size of the 3 smaller pieces you cut out. You can use your finger to press the thermal pad and stick it. Use your fingernail to cut off the excess, if any.

[photo 3.3] X

5. After this, remove the transparent protective sheet from the 3 pieces of thermal pad and fixate the RBPi4 compute module to the thermal block using the 4 x ISO7380 M2.5 screws:

[photo 3.4] X

[photo 3.5] X

6. Finally, stick the remaining piece of thermal pad (27 x 20 mm) on the contact surface in the external side of the thermal block. That is, on top of the "tower" with 2 tiny holes. Follow the same procedure you already did with the 3 smaller pieces, but don't remove the transparent protective sheet yet.

[photo 3.6] X

Step 4: Assemble the Main Board into the aluminum case bottom

1. Take the main board from its case:

[photo 4.1] X

2. Take 7 x ISO7380 M3 screws:

[photo 4.2] X

3. Plug the RBPi4 (with the thermal block) on the Main Board's RBPi4 socket, the big one with 2 rows of 20 pin-holes each. Put attention to not bending any pin. Fixate the thermal block using the 4 x M2.5 screws from the backside.

[photo 4.3] X

[photo 4.4] X

4. Remove the transparent protective sheet from the piece of thermal pad sticked in the thermal block bottom and softly place the Main Board in the aluminum case bottom. Fixate it using 7 x M3 screws (DIN).

[photo 4.5] X

Assembling Zynthian Kit V5

Contents