Assembling Zynthian Kit V5.1

From ZynthianWiki
Jump to navigation Jump to search

1 Previous Requirements


1.1 BOM V5.1 kit


IMG 4251 fixed wiki.JPG
  • V5.1 Aluminum Case
    • Bottom
    • Top
  • Main Board
  • Control Board
  • Display
  • Raspberry Pi5
  • Thermal Block
  • Thermal Pad (1 piece of 6 x 2 cm)
  • Silicone Keypad
  • Rubber Feet (4 units)
  • Wiring
    • RBPi5 DSI display flat cable: 20cm long, 1.6cm wide, 1mm/0.5mm pitch
    • Control Board flat cable: 15cm long, 1cm wide, 0.5mm pitch
    • USB-C adapter + flat cable: 5cm long, 1cm wide, 0.5mm pitch
    • uSD-card adapter with flat cable: 5cm long, 1cm wide, 1mm pitch
  • Screws
    • 12 x ISO7380 M2.5x5mm black zinc-plated steel (the smaller ones with round head)
    • 21 x ISO7380 M3x5mm black zinc-plated steel (the slighty bigger ones with round head)
    • 10 x DIN7991 M3x6mm black zinc-plated steel (the ones with conic head)
    • 4 x DIN916 M3x4mm black zinc-plated steel (the headless ones)
    • 8 x Hexagonal Spacer M3x10mm brass
  • Mechanized Aluminum Knobs (4 units)
  • Power Supply: 24V, 1.5 Amp (1 unit)
  • SD-Card >= 32GB (NOT included in V5.1 kit)
  • Optional: CR2032 lithium battery (NOT included in V5.1 kit)


WARNING!!

For working, the V5.1 needs a SD-card with the ZynthianOS software. Learn how to download the SD-image and prepare your SD-card.


1.2 Tools Required


  • Allen Spanner 1.5 mm
  • Allen Spanner 2.0 mm
  • Scissors or Cutter (NOT included in V5 kit)
  • Rule meter (NOT included in V5 kit)


1.3 Time Required


Depending on your skills and ability it may take 1 to 3 hours.


2 General Advice


  • Read and follow carefully the assembling instructions. Don't ignore any guidance or recommendations. We are quite lazybones, so we should have had some important reason to write them.
  • Use the browser's zoom to magnify the details in the pictures. They have good resolution and will allow you to see all details you need.
  • Prepare the working space and the needed tools. A clean 120 x 60 cm table will be big enough. More is always welcome. Less is not recommended. Remove all stuff you don't need from the surface and prepare the tools you will need.
  • Ensure you have good lighting in the working area. Having good lightning will ease delicate operations, especially those involving smaller parts.
  • Please, be extremely delicate when manipulating the flat cable connectors (FPC). They are the weakest parts and can be easily broken. Look carefully at the photos/videos and proceed just in the way we recommend. Use 2 hands, one finger from each hand. Avoid manipulating the connectors with a single hand or finger and don't use any tool for this.
  • Don't be impatient. If you have doubts or you don't know how to go on, please, stop assembling and ask in the forum or send an email to support@zynthian.org. It's better to wait some hours to get an answer than waiting for days/weeks to get a replacement part.
  • Keep your hands clean so you can enjoy a nice unit after finishing.


WARNING!!

DON'T USE FORCE! NEVER! Some parts are really delicate, especially flat cable connectors (FPC), and you can easily break something if you are brute. Assembling the V5 unit is not difficult at all, but it's a clock-maker work. A beginners one that almost everyone can do, but clock-maker's task anyway. If you are not very used to manipulate this kind of stuff, please, proceed slowly. Thinking twice will let you build it once.


3 BOTTOM PART


3.1 Dump the screws from the bag in a suitable receptacle


Capture000028 fixed wiki.JPG

Be careful when opening the screws bag. Some of them are really small and you can easily lose them. Please, don't dump them on the table's surface or on top a piece of paper. We recommend to dump the bag's content in a small tray, so you can look at and take out the parts easily while getting them well confined so they can't be lost.

Pay special attention to the 4 tiny headless screws used to secure the knobs. They are really small!! You can screw them into the knobs as a first step to avoid losing them during the build process.

Now is a good time to familiarize yourself with the different screw models available. Take a close look at the content of the screws bag and try to identify:

  • 12 x ISO7380 M2.5x5mm black zinc-plated steel => the smaller ones with round head
  • 21 x ISO7380 M3x5mm black zinc-plated steel => the slighty bigger ones with round head
  • 10 x DIN7991 M3x6mm black zinc-plated steel => the ones with cone-shaped head
  • 4 x DIN916 M3x4mm black zinc-plated steel => the headless ones
  • 8 x Hexagonal Spacer M3x10mm brass => they are the only brass parts



3.2 Stick the rubber feet to the aluminum case bottom


Build51 case bottom 01.jpeg
Build51 case bottom 02.jpeg

1. Look for the aluminum case bottom part in the "V5" case package:


IMG 4041 fixed wiki.JPG

2. Look for the 4 x rubber feet inside the wiring bag, in the "Screen and Bits" case:


Build51 case bottom rubber feet.jpeg

3. Stick the 4 x rubber feet to the aluminum case bottom part. This will prevent scratches during the assembly process.


3.3 Plug the display ribbon cable into the RPi5


Build51 display cable rpi5.jpg

1. Look for the display ribbon cable in the "Screen and Bits" case. It's 20cm long and 1.6cm wide:


Build51 rpi5.jpg

2. Look for the RPi5 in the "Accessories" case.


Build51 rpi5 display cable plugged 01.jpg
Build51 rpi5 display cable plugged 02.jpg

3. Open the RPi5's DSI connector by softly pulling up on both sides of the tiny black/grey tongue at once. It opens only about 2mm. When it's totally open, push the ribbon cable inside, straight down, with the black shiny side at the end of the cable facing out (towards the HDMI printed on the RPi5 board). The copper contacts on the end of the cable that are pushed into the connector should be facing the RPi5 Ethernet jack. All flat cables in the V5 kit are reversible, so you use can either end, while taking care to have the black shiny side facing away from the Ethernet jack. When the cable is tightly inserted, close the connector by pushing down on the tongue with 2 fingers, one of each hand. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK. Note: There is no blue side shown in the photographs.


WARNING!!

When possible, use 2 hands to manipulate the fragile FPC connectors. You will control the applied force a lot better compared to just using a single hand. If you can't use both hands, take extreme care. Indeed, you should always take extreme care while manipulating FPC connectors.


Note:

If you break an FPC's connector tongue, you could work around the problem using a hot glue gun. Not nice, but it works quite well!


3.4 Install the thermal block


Zynthian V5.1 gets a 20% extra power from the RPi5 by overclocking the CPU up to 3 GHz. For this to work properly, we need to remove the heat generated by the RPi5's components. As we don't want a noisy fan, prone to failure, pushing dust inside our nice case, we are using the aluminum case as a huge heat-sink. This is achieved by the thermal block, a solid aluminum block that closely contacts with the RPi5's chips and serves as a heat-highway to the aluminum case bottom, and from there, to the rest of the aluminum case. When your zynthian V5.1 is working hard, or when external temperature is high enough, you will note the aluminum case getting hot. This is good because it means the thermal block is doing its job of transferring heat from the inside to the aluminum case body, where it's dissipated to the ambient environment.

Having understood all this, you may realize this is a key step for getting your V5.1 working at 100% of its capacity, so don't be in a hurry and take your time to do a good job. Let's start!




Build51 thermal block 01.jpg

1. Look for the thermal block in the accessories case.


IMG 4045 fixed wiki.JPG
Thermal pad cut v51.png
IMG 4142 fixed wiki.JPG

2. Look for the piece of thermal pad in the wiring bag, in the "Screen and Bits" case. It is a piece of approximate size of 60 x 20 mm, gray on one side and blue on the other.


3. Using the rule-meter and the scissors or cutter, cut 4 little pieces of thermal pad with these apr sizes:


  • 20 x 28 mm
  • 19 x 12 mm => This is the most important!
  • 14 x 9 mm
  • 11 x 11 mm


Build51 thermal block 02.jpg

4. Remove the blue protective sheet from the 3 smaller pieces and stick them to the inner side of the thermal block, the one that makes contact with the RPi5. You'll recognize it because it has 3 small rectangular islands that fit the size of the 3 smaller pieces you cut out. You can use your finger to stick it, pressing and extending the thermal pad. Use your fingernail to cut off the excess, if any.


IMG 4191 fixed wiki.JPG

5. Take 4 x ISO7380 M2.5 screws. They are the smaller ones with rounded head.


Build51 rpi5 thermal back.jpg

6. Remove the transparent protective sheet from the 3 pieces of thermal pad and fix the RBPi4 compute module to the thermal block using the 4 x ISO7380 M2.5 screws.


Build51 rpi5 thermal display cable bending 00.jpg
Build51 rpi5 thermal display cable bending 03.jpg
Build51 rpi5 thermal display cable bending 01.jpg
Build51 rpi5 thermal display cable bending 02.jpg
Build51 rpi5 thermal display cable bending 04.jpg

7. Before installing the "RPi5 + thermal block" assembly in the main board, you must fold the display cable adequately, so it goes in the right direction. You must fold it twice, putting attention to the pictures and using your "common sense". The first fold is straight and the second one is at 45º, so you get the cable going out the RPi5 with the text "Display-cable-200mm" on the down side. We show several pictures from different angles. Zoom in as needed until you have clear how to proceed. Take your time and think twice to do once.


Build51 rpi5 thermal finished.jpg

8. Finally, stick the remaining piece of thermal pad (27 x 20 mm) on the contact surface in the external side of the thermal block. That is, on top of the big "tower" with 2 tiny holes. Follow the same procedure you already did with the 3 smaller pieces, but don't remove the protective sheet yet. This will be done later, when installing the module in the aluminum case bottom.


3.5 Assemble the Main Board into the aluminum case bottom


Build51 mainboard.jpg

1. Take the main board from its case.


Build51 holder cover.jpg

2. Look for the SD-card holder cover in the wiring bag. This little piece of plastic is just to make sure you can't accidentally push the SD card into the gap between its slot and the case, thus losing it. But ... can this happen? Well, it's not easy, but we provide this nice piece of plastic for a reason ;-)


Build51 mainboard holder cover detail.jpg
Build51 mainboard holder cover.jpg

3. Plug the SD-card holder cover on top the SD-card holder. Please, put attention to the orientation. The tiny plastic feet must get inside the 2 corresponding tiny holes, then push slowly until it's totally inserted. It should get clipped. Once it's inserted, don't try to remove it or you probably would break the little plastic feet. This is a one-time operation.


IMG 4191 fixed wiki.JPG

4. Take 4 x ISO7380 M2.5 screws. They are the smaller ones with rounded head.


Build51 mainboard rpi5.jpg

5. Plug the RBPi5 (with the thermal block attached) on the Main Board's RBPi socket, the big one with 2 rows of 20 pin-holes each. Pay attention to not bend any pins. Also note that the display flat cable should pass through the rectangular hole in the main board, as seen in the photos (zoom in if you have doubts).


Build51 mainboard rpi5 bottom secured.jpg

6. Fix the thermal block to the main board from the backside using the 4 x M2.5 screws.


Note:

At this point, it's recommended to do steps 3.6 and 3.7 in advance. Most people find more comfortable to plug the SD-card & USB-C adaptors before assembling the main board in the aluminum case. Up to you!


IMG 4221 fixed wiki.JPG

7. Take 7 x ISO7380 M3 screws. They are the mid-size ones with rounded head.


Build51 mainboard alucase.jpg
Build51 mainboard alucase secured.jpg

8. Remove the protective sheet from the piece of thermal pad stuck to the thermal block bottom and softly place the main board in the aluminum case bottom. You will find it more comfortable to grab the thermal block to do this operation. Fix it using the 7 x ISO7380 M3 screws.


3.6 Plug SD-card adapter


IMG 4270 fixed wiki.JPG

1. Look for the SD-card adapter in the wiring bag.


Build51 sdcard adapter 01.jpg

2. Carefully, using 2 fingers, one on each hand, pull the main board's SD-card connector tongue until it's totally open.


Build51 sdcard adapter 02.jpg

3. Insert the SD-card adapter's ribbon cable. It must be inserted straight, with the blue side facing down.


Build51 sdcard adapter 03.jpg

4. When it's totally inserted, push the tongue with 2 fingers at once and close the connector. Pay attention to ensure the cable does not move out of the connector. If it's not fully inserted or not straight enough, repeat the operation until it's OK.


Build51 sdcard adapter 04.jpg

5. Plug the SD-card adapter into the RPI5's SD-card holder. The connector is rotated 90º respect to the cable, so you must softly bend the ribbon cable to get it plugged-in. Check the pictures and proceed slowly, always using the minimum amount of force.


3.7 Plug USB-C adapter


IMG 4258 fixed wiki.JPG

1. Look for the USB-C adapter in the wiring bag.


IMG 4291 fixed wiki.JPG

2. Carefully, using 2 fingers, one on each hand, pull the main board's USB-C connector tongue until it's totally open.


IMG 4294 fixed wiki.JPG

3. Insert the USB-C adapter's ribbon cable. It must be inserted straight, with the blue side facing down.


IMG 4303 fixed wiki.JPG


4. When it's totally inserted, push the tongue with 2 fingers at once and close the connector. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK.


Build51 mainboard usbc adaptor 02.jpg
Build51 mainboard usbc adaptor 01.jpg

5. Plug the USB-C connector into the RPi5's USB-C socket.


3.8 Secure the thermal block to the aluminum case bottom


Capture000079 fixed wiki.jpg

1. Look for 2 x DIN7991 M3 screws. They have countersunk flat heads.


Capture000081 fixed wiki.jpg

2. Flip the aluminum case bottom and look for the 2 countersunk holes. Using the Allen wrench, punch the thermal pad through the holes.


Capture000082 fixed wiki.jpg

3. Screw the 2 bolts and tighten them well enough, but not too much.


4 TOP PART


4.1 Secure the top-spacers on the control board


Capture000060 fixed wiki.JPG

1. Take the control board from its case. You don't need the silicone buttons yet.


Capture000071 fixed wiki.JPG

2. Take the 8 x brass spacers 10mm and 8 x ISO7380 M3 screws (the mid-size ones with round head).


Capture000068 fixed wiki.JPG

3. Secure the 8 x spacers on the control board's top side. To do this, insert the bolt from the back side and while holding it with your finger, fasten the spacer with the other hand until it's tight. You don't need a wrench for this, but you can use one if you like.


4.2 Assemble the display on the control board


Capture000072 fixed wiki.JPG

1. Take the display from its case. Don't remove the protective sheet yet. Flip the display and remove the 4 yellow protective sheets from the outer spacers. You can use your fingernail or a cutter for this operation.


IMG 4191 fixed wiki.JPG

2. Take 4 x ISO7380 M2.5 screws (the smaller ones with round heads).


Capture000076 fixed wiki.JPG
Capture000073 fixed wiki.JPG

3. Secure the display to the control board's top side using the 4 x small M2.5 screws. Don't tighten these bolts yet!!! The display must be loose to get a good fit with the aluminum case top part. You will tighten these screws later. Pay attention to the display orientation. The display FPC connector for the flat cable must be accessible through the main board's square hole.


4.3 Plug the flat ribbon cable into the control board


Capture000142 fixed wiki.jpg

1. Look for the control flat ribbon cable in the wiring bag. It's grey with blue tips, 15cm long and 1cm wide.


Capture000084 fixed wiki.jpg
Capture000085 fixed wiki.jpg

2. Carefully, using 2 fingers, one on each hand, pull the control board's FPC connector tongue until it's totally open.


Capture000086 fixed wiki.jpg

3. Insert the ribbon cable into the FPC connector. It must be inserted straight, with the blue side facing down. All flat cables in the V5 kit are reversible, so you can take any of the 2 caps, while taking care of placing the blue side facing down.


Capture000087 fixed wiki.jpg

4. When it's totally inserted, push the tongue with 2 fingers at once and close the connector. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK.


4.4 Secure the control board, silicone buttons and display to the aluminum case top


Capture000039 fixed wiki.jpg

1. Look for the aluminum case top part.


Capture000099 fixed wiki.jpg

2. Look for 8 x DIN7991 M3 screws. They have countersunk flat heads.


Capture000089 fixed wiki.jpg

3. Place the silicone button pad on top the control board. Note the tiny silicone studs in the bottom of the pad and pay attention to make them fit into the small positioning holes on the control board. Once it's done, softly push the button pad to the side to check whether it sits snug in it's place. The pad shouldn't move when you try pushing it to the side.


Capture000094 fixed wiki.jpg

4. Use the "Screens & Bits" case as a mounting stand and place the control board on it, as shown in the picture.


Capture000095 fixed wiki.jpg

5. Place the aluminum case top part over the control board taking care of orientation and proceeding slowly. It's a good time to remove the display's protective sheet, or at least, fold the green tab out of the way so the display makes a good fit into the case's window.


Capture000101 fixed wiki.jpg

6. Secure the control board with the 8 x M3 countersunk screws. Again, tighten enough, but not too much.


Capture000102 fixed wiki.jpg

7. Flip the top part and place it over the carton-stand again. Now is the right moment to tight the 4 display screws from step 4.2 (do you remember?).


Build51 both parts separated.jpg

8. Congratulations! We are ready to join everything together.


5 JOINING BOTH PARTS AND CLOSING THE CASE


If you want to place a CR2032 lithium battery for the RTC (Real Time Clock), this is a good moment. If not, don't worry, you can open the case and do it later.


5.1 Plug the display flat cable into the display


Build51 join parts display 01.jpg

1. Take the cardboard box labeled as V5, which contained the aluminum case. We will use it as a mounting tool in this step. Place it at right side of the zynthian's bottom part forming a 90º angle, as shown in the picture.


Build51 join parts display 02.jpg

2. Place over the box the zynthian's top part, with the display surface touching the cardboard and the display connector at left. Just like shown in the picture.


Build51 join parts display 03.jpg

3. Using two fingers, one on each hand, softly pull the display's connector tongue until it's open. Insert the flat ribbon cable coming from the RPi5 into it so the black side is face down and the copper contacts face up.


Build51 join parts display 04.jpg

4. When it's totally inserted, softly push the tongue using 2 fingers, one on each hand, until it's totally closed. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK.


Note:

Probably you are thinking that we could use longer cables so these final steps would be easier. And you are right, it would be easier to assemble, but the resulting device wouldn't be so good. Longer cables means more EMI (Electro-Magnetic Interference). The DSI signal coming out the RPi is specially noisy and although the DSI cable we use already include some EMI shielding, the audio circuitry is close, just a few centimeters, and we prefer to reduce EMI to the minimum. Think that you assemble your zynthian once, but you (hopefully!) will use it for years and i'm pretty sure you want the highest quality of sound, so it's worth the extra effort to connect shorter cables.

5.2 Plug the control flat cable into the main board


Build51 join parts control 01.jpg
Build51 join parts control 02.jpg

1. Relocate the zynthian's top part so it's partially fitted with the bottom part, forming a 90º angle. Please, move it slowly and take special care of not forcing the display cable that you just connected in the step above. You can remove the cardboard box as it's not longer needed.


Build51 join parts control 03.jpg
Build51 join parts control 04.jpg

2. Using two fingers, one on each hand, softly pull the main board's control-1 connector tongue until it's open. Insert the flat ribbon cable coming from the control board (top part). Do it straight, without bending or twisting it in any way, so the blue side is face down.


Build51 join parts control 05.jpg

3. When it's totally inserted, softly push the tongue using 2 fingers, one on each hand, until it's totally closed. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK.


5.3 Close the aluminum case


Build51 join parts close 01.jpg

1. Without moving the parts from the last position, you are ready to close the case. Now you are really close to finish the assembling process!


Build51 join parts close 02.jpg

2. Close the case slowly, taking care that the cables are not being trapped. Probably you would need to help the control flat cable to get into the case while closing it.


Build51 join parts close 03.jpg

3. Before securing the case top and inserting the knobs, it's a good time to burn a SD-card with the latest zynthian software image and check everything is working OK. Please, use a good quality SD-card and follow the instructions carefully.

First boot could take some time. After a minute or so, you will see the display fill with upside-down text, then a login prompt, which will automatically continue. Don't be impatient - wait perhaps 5 minutes until you see the splash screen with the logo. If the display remains black after 1 minute (no upside-down text is displayed), please re-check the instructions and re-burn the SD-card again. If this still doesn't work, try with a different SD-card before reporting in the forum. For solving SD-card issues, it could be useful to check the RPi5 status LEDs.

Once you see the splash screen, it could take a few more minutes until the system is ready. You deserve a beer, or at least some some tea or coffee. When the first-boot process finishes, the Zynthian will reboot and you will be in the main menu, ready to play.


Capture000124 fixed wiki.jpg
Capture000125 fixed wiki.jpg

5. If everything worked fine and your zynthian is alive, please, finish the task before start exploring your new zynthian V5.1. Take the remaining 6 x ISO7380 M3 screws and secure the case, 3 on each side. Tighten enough, but not too much.


5.4 Attach and secure the knobs


Capture000131 fixed wiki.jpg

1. Take the 4 x mechanized aluminum knobs from the wiring bag and the 4 x super-tiny DIN916 M3 screws (headless screws).


Capture000132 fixed wiki.jpg
Capture000133 fixed wiki.jpg

2. Insert the headless screw in the allen wrench and screw it partially into the knob side hole, until its head is slightly over the knob side.


Capture000135 fixed wiki.jpg

3. Repeat the step for the 4 knobs.


Capture000136 fixed wiki.jpg

4. Turn the 4 x rotary encoders until the flat cotter is pointing outside.


Capture000137 fixed wiki.jpg

5. Tighten the headless screws. Enough but not too much.


Capture000140 fixed wiki.jpg
Capture000158 fixed 1024.jpg

6. Congratulations! Your Zynthian V5.1 is ready to boot for the first (or second??) time. If you didn't yet, it's time to burn a SD-card with the latest zynthian software image. Please, use a good quality SD-card and follow the instructions carefully.

First boot could take some time. Don't be impatient and wait until you see the splash screen with the logo. If the display remains black after 1 minute, please, re-check the instructions and re-burn the SD-card again. If this still don't work, try with a different SD-card before reporting in the forum. For solving SD-card issues, it could be useful to check the RPi5 status LEDs.

Once you see the splash screen, it could 1-2 minutes to finish the configuration process. You deserve a beer (hey!! don't abuse if you already took one!!), or at less some tea or coffee. When the first-boot process finishes, the zynthian will reboot and you will be in the main menu, ready to play.

It's time to remove the display's protective sheet (please, do it!!) and take a look to the user's guide!