3,418
edits
Changes
Jump to navigation
Jump to search
Line 92:
Line 92: − + Line 113:
Line 113: − + − − These are 2 separated connectors with a 3-wire harness each, ended with 3 x 1-pin DuPont connectors. One of them have a '''red circle sticker that MUST be mounted on the Right (R) audio Out'''" − − Insert the jack connectors into the 2 holes labelled as ''audio OUT''. You have to insert them from inside the case and secure them with the washers and nuts from the outside. The washers will keep the nut from damaging the case. Use a wrench for tightening the nuts, but not too much!! − − − [[File:Zynthian_case_connectors_v41_red.jpg|400px]] − [[File:IMG_2890_OK_1024_fixv41.JPG|400px]] − [[File:IMG_2895_OK_1024_red.JPG|400px]] − − ===Secure the balanced audio input jack-TRS connectors=== − − These are 2 separated connectors with a 3-wire harness each, ended with 3 x 1-pin DuPont connectors. − − Insert the jack connectors into the 2 holes labeled as ''audio IN''. You have to insert them from inside the box and secure them with the washers and nuts from the outside. The washers will keep the nut from damaging the case. Use a wrench for tightening the nuts, but not too much! + Line 301:
Line 287: − + − Every TSR connector has 3 colored wires like this:+ − * '''Red''' -> Signal ++ − * '''White''' -> Signal - − * '''Black''' -> Ground − Each TSR connector must be connected to the 10-pin header (J1) on the Hifiberry DAC+ADC Stage:+ − First, connect the audio OUT TSR connectors like this: − − [[File:HifiBerryDACADC-Stage-connection-OUT.png|600px]] − − And then, the audio IN TSR connectors like this: − − [[File:HifiBerryDACADC-Stage-connection-IN.png|600px]]
Building a Zynthian Box using official Kits v4.2-v4.6 (view source)
Revision as of 00:23, 7 March 2021
, 00:23, 7 March 2021no edit summary
+ '''1 x Zynductor'''
+ '''1 x Zynductor'''
[[File:Rbpi4 shop.jpg|330px]][[File:HifiBerryDACADC-Stage-top.jpg|330px]][[File:IMG_2775_OK_shop.JPG|330px]][[File:Controllers_shop.jpeg|330px]][[File:Zynaptik shop.jpeg|330px]][[File:Ribbon_shop.jpeg|330px]][[File:Zynthian_alucase_v41-persp.jpg|330px]][[File:IMG_2887_OK_1024.JPG|330px]][[File:IMG_2887_OK_1024.JPG|330px]][[File:Boltsnuts.JPG|440px]][[File:IMG_2756_OK_shop.JPG|220px]]
[[File:Rbpi4 shop.jpg|330px]][[File:HifiBerryDACADC-Stage-top.jpg|330px]][[File:IMG_2775_OK_shop.JPG|330px]][[File:Controllers_shop.jpeg|330px]][[File:Zynaptik shop.jpeg|330px]][[File:Ribbon_shop.jpeg|330px]][[File:Zynthian_alucase_v41-persp.jpg|330px]][[File:IMG_2887_OK_1024.JPG|400px]][[File:IMG_2887_OK_1024.JPG|400px]][[File:Boltsnuts.JPG|440px]][[File:IMG_2756_OK_shop.JPG|220px]]
===Unboxing the Zynthian Kit v4===
===Unboxing the Zynthian Kit v4===
Let's go!!
Let's go!!
===Secure the balanced audio output jack-TS connectors ===
===Secure the ZynAuCon Audio Connectors Board ===
The ZynAuCon module improves and simplifies the audio wiring by using a small ribbon cable for driving the 4 balanced channels (2 inputs + 2 outputs) to the 4 high-quality Neutrik TSR case-connectors. For mounting the ZynAuCon, secure the 2 x 15mm separators with 2 x black-anodized bolts M2.5. Next, you have to insert the board from inside the case and secure them with the 4 x nuts from the outside. Use a wrench for tightening the nuts, but not too much, and take care of not damaging the surface of the nice aluminum case!!
[[File:IMG_2886_OK_1024.JPG|400px]]
[[File:IMG_2886_OK_1024.JPG|400px]]
===Connect the TSR Balanced Audio Connectors to the Hifiberry DAC+ADC Stage===
===Connect the ZynAuCon Audio Connectors Board to the Hifiberry DAC+ADC Stage===
Plug the little 2x10 ribbon cable on the Hifiberry's J1 connector. Next, plug the other end on the ZynAuCon board. Observe that the ribbon cable must be bent forming a 90º angle, so it fits perfectly the space and distance between the 2 IDC connectors.
[[File:HifiBerryDACADC-Stage-connection-OUT.png|600px]]
FYI, this is the specification for the 10-pin header (J1) on the Hifiberry DAC+ADC Stage:
[[File:HifiBerryDACADC-Stage-header.jpg|450px]]
[[File:HifiBerryDACADC-Stage-header.jpg|450px]]
===Connect the Display===
===Connect the Display===