Line 76: |
Line 76: |
| ===Zynthian Bundle All Kit v3=== | | ===Zynthian Bundle All Kit v3=== |
| | | |
− | A Zynthian Kit is a set of electronic parts. The ''official'' Zynthian Bundle All Kit v3 consists of specific parts: | + | A Zynthian Kit is a set of electronic and mechanic parts. The ''official'' Zynthian Bundle All Kit v3 consists of these specific parts: |
| | | |
| + '''4 x Controller Modules + Wiring''' | | + '''4 x Controller Modules + Wiring''' |
Line 110: |
Line 110: |
| ===Prerequisites=== | | ===Prerequisites=== |
| | | |
− | Assembling your Zynthian Kit V3 is not difficult at all: you need is your attention, a screwdriver, and an adjustable wrench. You don't need to solder anything, just put it together and connect the wires. | + | Assembling your Zynthian Kit V3 is not difficult at all: you need your attention, a screwdriver, and an adjustable wrench. You don't need to solder anything, just put it together and connect the wires. |
| | | |
| Read the instructions and observe the detailed photos carefully. If you get in trouble you can ask the community: | | Read the instructions and observe the detailed photos carefully. If you get in trouble you can ask the community: |
Line 127: |
Line 127: |
| ===Secure the MIDI connectors=== | | ===Secure the MIDI connectors=== |
| | | |
− | Insert each MIDI from the outside and secure them with the bolt from the inside. | + | Insert each MIDI connector, from the outside and secure them with the bolt from the inside. |
| | | |
| [[File:IMG_2401.JPG|600px]] | | [[File:IMG_2401.JPG|600px]] |
Line 184: |
Line 184: |
| [[File:IMG_2410.JPG|600px]] | | [[File:IMG_2410.JPG|600px]] |
| | | |
− | The zynaptik board has some extra circuitry which doesn't have anything soldered on it. These are used for modifying the board, and it is fully functional as it is. | + | The zynaptik board has some extra circuitry which doesn't have anything soldered on it. These are used for adding extra functionality to the board. |
| | | |
| ===Mount the Display=== | | ===Mount the Display=== |
Line 318: |
Line 318: |
| 4. After 5-10 seconds, the zynthian UI will be shown | | 4. After 5-10 seconds, the zynthian UI will be shown |
| | | |
− | If you get the Zynthian UI, then you have assembled the Zynthian box correctly. | + | If you get the Zynthian UI, then you have assembled the Zynthian box correctly. Congratulations! |
| | | |
| [[file:IMG_2490.JPG|600px]] | | [[file:IMG_2490.JPG|600px]] |
Line 348: |
Line 348: |
| The selector must go down when rotating clockwise and go up when rotating counter-clockwise. If the rotation sense is reversed, you should check the wiring. Perhaps one of the connections are faulty. The wires' color sequence should be red, black, yellow, green. | | The selector must go down when rotating clockwise and go up when rotating counter-clockwise. If the rotation sense is reversed, you should check the wiring. Perhaps one of the connections are faulty. The wires' color sequence should be red, black, yellow, green. |
| | | |
− | 4. Select the ZynAddSubFX engine, select channel #1, select 'Collection' and preset 'Metal Drips' present. | + | 4. Select the ZynAddSubFX engine, select channel #1, select bank 'Collection' and preset 'Metal Drips'. |
| | | |
| [[File:IMG_2497.JPG|600px]] | | [[File:IMG_2497.JPG|600px]] |
Line 360: |
Line 360: |
| If one of the controllers doesn't work correctly, check the wiring again. | | If one of the controllers doesn't work correctly, check the wiring again. |
| | | |
− | 6. Push SELECT to move to the next controller screen. Bold push (a push lasting a few seconds) to select a controller screen from the list. | + | 6. Push SELECT to move to the next controller screen. Bold push (a push lasting about 1 second) to select a controller screen from the list. |
| | | |
| 7. Push BACK. You should go back to the 'Preset Selection' screen. | | 7. Push BACK. You should go back to the 'Preset Selection' screen. |