Difference between revisions of "Adding Extra I/O with the Zynaptik Module"

From ZynthianWiki
Jump to navigation Jump to search
Line 36: Line 36:
  
 
* '''16xSWITCH''' => Only MCP23017, use the 16 GPIOs as customizable switches
 
* '''16xSWITCH''' => Only MCP23017, use the 16 GPIOs as customizable switches
* '''8xSWITCH''' => Only MCP23017, use the 8 GPIOs as customizable switches (Bank A)
 
 
* '''4xAD''' => Only ADS1115 (use the 4 ADs for Analog Input, obvious)
 
* '''4xAD''' => Only ADS1115 (use the 4 ADs for Analog Input, obvious)
 
* '''16xSWITCH + 4xAD''' => MCP23017 + ADS1115, use the 16 GPIOs as customizable switches
 
* '''16xSWITCH + 4xAD''' => MCP23017 + ADS1115, use the 16 GPIOs as customizable switches
* '''8xSWITCH + 4xAD''' => MCP23017 + ADS1115, use the 8 GPIOs as customizable switches (Bank A)
 
  
 
After saving, you may want to configure your switches and/or analog inputs.
 
After saving, you may want to configure your switches and/or analog inputs.

Revision as of 08:24, 21 August 2020

The Zynaptik module allows to solder on it 3 extra submodules and a 40 pin header for interfacing them:

Zynaptik top.jpg


Zynaptik 40pin header.png

+ Secondary MCP23017 (Digital I/O): It uses I2C address 0x21 and the 2 interrupt lines are connected to the RBPi GPIO. INTA to GPIO27 (pin 36) and INTB to GPIO25 (pin 37). The digital I/O are labelled as GPAx & GPBx on the Zynaptik's header schematic.

You can use it for adding up to 16 extra switches to your zynthian.

Buy MCP23017 DIP


+ ADS1115 (MOD-1 Analog Input): It uses I2C address 0x48 by default. The 4 analog input pins are labelled as ADx on the Zynaptik's header schematic.

You can assign the Analog Inputs to MIDI events like Pitch-Bending, CC or ChanPress. This can be used for connecting CV-IN or for controlling sound engine parameters using analog sensors.

Buy ADS1115 module


+ MCP4728 (MOD-2 Analog Output): It uses I2C address 0x60 by default. The 4 analog output pins are labelled as DAx on the Zynaptik's header schematic.

It's currently unimplemented. The highest honor is deserved to the brave who kill this dragon ...

Buy MCP4728 module


1 Configuring the Zynaptik Module from the Webconf

Zynthian webconf wiring zynaptik config.png

First, you should choose the right configuration for your zynaptik module depending on the extra modules you have soldered on it:

  • 16xSWITCH => Only MCP23017, use the 16 GPIOs as customizable switches
  • 4xAD => Only ADS1115 (use the 4 ADs for Analog Input, obvious)
  • 16xSWITCH + 4xAD => MCP23017 + ADS1115, use the 16 GPIOs as customizable switches

After saving, you may want to configure your switches and/or analog inputs.

2 Configuring Zynaptik Customizable Switches

Simply add the switches pins to the list. Zynaptik MCP23017 pins start at 200. You don't need to add all the 16/8 available switches. If you only want to use 2, simply add "200,201". After saving, you will see that the extra custom switches are available for configuration.


3 Configuring Zynaptik Analog Input

Zynthian webconf wiring zynaptik ad.png

Simply configure your analog inputs from the webconf's wiring section in the same way you configure your custom switches.