Simple RPF Touchscreen Zynthian - Revision history

Gmeader: /* Configure Zynthian software */

2017-11-03T20:19:32Z

Configure Zynthian software

2017-11-03T20:14:23Z

Configure Zynthian software

2017-10-02T17:50:06Z

2017-09-16T20:50:25Z

added pictures

2017-09-16T20:41:08Z

Info on Zynthian Admin webpage

2017-09-16T20:24:23Z

2017-09-16T19:53:43Z

add info about enabling SSH

2017-08-25T21:31:01Z

2017-08-17T07:28:57Z

Configure Zynthian software

2017-08-17T07:27:52Z

Setup

@@ Line 38: / Line 38: @@
 # Login to your Zynthian's admin webpage (password: raspberry)
 [[File:ZynLogin.png]]
-# Change the display to Generic HDMI, and set rotation.
+# Change the display to Generic HDMI, and set lcd_rotate=2 in the Config.
 [[File:HDMI.JPG]]
-# Change the Audio device to USB device
+# Change the Audio device to USB device. Need to provide the proper device name in the Jackd Options: replace ''hw:0'' with the correct device name. Find the device name by giving the Linux command: '''aplay -L''' at the command line
 [[File:ZynAudio.png]]
 # Change the Wiring to DUMMIES

@@ Line 38: / Line 38: @@
 # Login to your Zynthian's admin webpage (password: raspberry)
 [[File:ZynLogin.png]]
-# Change the display to Generic HDMI
+# Change the display to Generic HDMI, and set rotation.
-[[File:ZynDisplay.png]]
+[[File:HDMI.JPG]]
 # Change the Audio device to USB device
 [[File:ZynAudio.png]]

← Older revision		Revision as of 17:50, 2 October 2017
Line 2:		Line 2:

	This page is still being developed. Still trying to get it to work, and get these instructions exactly correct. Use at your own risk. Please edit this page if you have corrections.		This page is still being developed. Still trying to get it to work, and get these instructions exactly correct. Use at your own risk. Please edit this page if you have corrections.
		+	The Zynthian SD image won’t work without a proper audio device (DAC). The RBPi integrated “audio device” is not suitable because it sounds poor and has latency. The SD image is pre-configured to work with HifiBerry DAC+, although you can use any DAC that works with RBPi (i.e. any I2S device).
		+	These instructions will attempt to configure the Zynthian image to work with the RBPi integrated “audio device” (even though it has poor performance) or an inexpensive USB audio adapter.

	Forum posting on this topic: https://discourse.zynthian.org/t/official-rbpi-touchscreen-7/430/23		Forum posting on this topic: https://discourse.zynthian.org/t/official-rbpi-touchscreen-7/430/23

@@ Line 35: / Line 35: @@
 # Login to your Zynthian's admin webpage (password: raspberry)
 # Change the display to Generic HDMI
 # Change the Audio device to USB device
 # Change the Wiring to DUMMIES
   - '''update zynthian software''' from the admin menu

@@ Line 23: / Line 23: @@
 # Connect the touch display to the Raspberry Pi using the included instructions
 # Insert the MicroSD card into the Raspberry Pi
-# Connect the Raspberry Pi to the Internet using a Ethernet cable (or connect using WiFi - see below)
+# Connect the Raspberry Pi to your local router using a Ethernet cable (or connect using WiFi - see below)
 # Connect the power Adapter to the Raspberry Pi and plug it into the wall.
 # The Raspberry Pi will boot up Zynthian.
 # To configure, connect to Zynthian using a web browser.
 =Configure Zynthian software=
-Connecting to your Zynthian box http://wiki.zynthian.org/index.php/Accessing_Zynthian_from_your_computer
+Use a web browser to access your Zynthian box's admin web page .  Depending on your setup you might try to just use '''http://zynthian.local/''' - if that doesn't work You need to enter the IP address of your Zynthian.
-Use a web browser to access your Zynthian box's admin web page .  Depending on your setup you might try to just use '''http://zynthian.local/''' - if that works, you don't need the IPaddress. Otherwise, You have to figure out what the Zynthian box's IP address is. If your Zynthain is connected with an Ethernet cable to your router, your router may have an admin interface (built-in webpage) that may show the IP address of connected devices)
+# Login to your Zynthian's admin webpage (password: raspberry)
   - '''update zynthian software''' from the admin menu

@@ Line 20: / Line 20: @@
 * or get the image mentioned here: https://discourse.zynthian.org/t/official-rbpi-touchscreen-7/430/22
 # Flash the software on to the MicroSD card using Etcher https://etcher.io/ (free software works on Mac, Windows or Linux)
 # Connect the touch display to the Raspberry Pi using the included instructions
 # Insert the MicroSD card into the Raspberry Pi

← Older revision		Revision as of 21:31, 25 August 2017
Line 2:		Line 2:

	This page is still being developed. Still trying to get it to work, and get these instructions exactly correct. Use at your own risk. Please edit this page if you have corrections.		This page is still being developed. Still trying to get it to work, and get these instructions exactly correct. Use at your own risk. Please edit this page if you have corrections.
		+
		+	Forum posting on this topic: https://discourse.zynthian.org/t/official-rbpi-touchscreen-7/430/23

	= Parts:=		= Parts:=

@@ Line 46: / Line 46: @@
   cd /zynthian/zynthian-sys/scripts
   ./update_zynthian.sh
-  ./update_zynthian.sh
+  ./update_zynthian.sh        (yes run it twice)
-  ./update_data.sh
+  ./update_zynthian_data.sh
 ==Step 1: Edit fb1 to fb0 in all these files:==

@@ Line 13: / Line 13: @@
 =Setup=
 # Download “Gorgona” SD Image for Zynthian for RBPi3 (8 GB) (you need bittorrent software (free) to download this)
- http://blog.zynthian.org/download/zynthian_gorgona_rbpi3-2016-12-21.img.torrent
- ** Download web page: https://discourse.zynthian.org/t/merry-zynthians-and-happy-new-sd-image/314
+* http://blog.zynthian.org/download/zynthian_gorgona_rbpi3-2016-12-21.img.torrent
 # Flash the software on to the MicroSD card using Etcher https://etcher.io/ (free software works on Mac, Windows or Linux)
 # Connect the touch display to the Raspberry Pi using the included instructions