Adding Extra I/O with the Zynaptik Module - Revision history

Jawn: /* Introduction */

2025-06-26T07:22:36Z

Introduction

Jofemodo: /* Introduction */

2022-03-11T00:32:02Z

Introduction

Jofemodo: /* Introduction */

2022-03-11T00:21:33Z

Introduction

Jofemodo: /* Introduction */

2022-03-11T00:12:43Z

Introduction

Jofemodo: /* Installing Zynaptik Expander Kit */

2022-03-10T23:55:25Z

Installing Zynaptik Expander Kit

Jofemodo: /* Eight digital input switches selecting Program Change events */

2021-10-26T10:26:52Z

Eight digital input switches selecting Program Change events

Jofemodo: /* Connect up to 4 Control pedals */

2021-10-26T10:26:30Z

Connect up to 4 Control pedals

Jofemodo: /* Configuring Zynaptik for Testing 21/08/2021 */

2021-10-26T10:26:06Z

Configuring Zynaptik for Testing 21/08/2021

Wyleu: /* Configuring Zynaptik for Testing 21/08/2021 */

2021-08-25T16:32:02Z

Configuring Zynaptik for Testing 21/08/2021

Wyleu: /* Eight digital input switches selecting Program Change events */

2021-08-25T16:29:54Z

Eight digital input switches selecting Program Change events

@@ Line 35: / Line 35: @@
 The voltage range is 0-5V. You can assign the Analog Inputs to MIDI events like Pitch-Bending, CC or ChanPress and use the analog signals for controlling any sound parameter. Analog Inputs can be combined with digital inputs from the MCP23017, allowing to configure up to 4 x CV/Gate-IN interfaces.
-'''+ MCP4728 (MOD-2 Analog Output):''' It uses different I2C address (0x60/0x61/0x64) depending of the zynaptik model. The 4 analog output pins are labelled as DAx on the Zynaptik's header schematic.
+'''+ MCP4728 (MOD-2 Analog Output):''' It uses different I2C address (0x60/0x61/0x64) depending on the zynaptik model. The 4 analog output pins are labelled as DAx on the Zynaptik's header schematic.
 The voltage range is 0-5V. You can assign MIDI events, like Pitch-Bending, CC or ChanPress, to the Analog Outputs. Analog Outputs can be combined with digital outputs from the MCP23017, allowing to configure up to 4 x CV/Gate-OUT interfaces.

@@ Line 3: / Line 3: @@
 The zynaptik module provides:
-* 3 standard MIDI ports (IN, OUT, THRU)
+* 3 x standard MIDI ports (IN, OUT, THRU)
 * 16 x digital Input/Output
 * 4 x Analog Input
@@ Line 18: / Line 18: @@
 include everything soldered on and they are ready to work.
-In the other hand, '''older modules''' (before 2021-04-01) only have MIDI circuitry soldered on. You must solder some parts for enjoying all the functionality. You can [https://shop.zynthian.org/shop/product/zynaptik-expander-kit-379 buy the Zynaptik Expander Kit] or order the parts by yourself.
+In the other hand, '''older modules''' (before 2021-04-01) only have the MIDI circuitry soldered on. For enjoying all the functionality (analog i/o) you must solder some parts. You can [https://shop.zynthian.org/shop/product/zynaptik-expander-kit-379 buy the Zynaptik Expander Kit] or order the parts by yourself.
 [[File:Zynaptik_top.jpg|900px]]
 [[File:Zynaptik_40pin_header.png|300px|right]]

@@ Line 8: / Line 8: @@
 * 4 x Analog Ouput
-'''New modules''' (''Zynaptik-2'' from 2021-04-01 & ''Zynaptik-3 Extended'' from 2022-03-10) include everything soldered on and they are ready to work:
+Latest ''Zynaptik-3 Extended'' modules (from 2022-03-10):
 [[File:Zynaptik3_top.jpg|900px]]
 [[File:Zynaptik2_top.jpg|900px]]
 In the other hand, '''older modules''' (before 2021-04-01) only have MIDI circuitry soldered on. You must solder some parts for enjoying all the functionality. You can [https://shop.zynthian.org/shop/product/zynaptik-expander-kit-379 buy the Zynaptik Expander Kit] or order the parts by yourself.

@@ Line 8: / Line 8: @@
 * 4 x Analog Ouput
-'''New modules''' (from 2021-04-01) include everything soldered on. Ready to work:
+'''New modules''' (''Zynaptik-2'' from 2021-04-01 & ''Zynaptik-3 Extended'' from 2022-03-10) include everything soldered on and they are ready to work:
 [[File:Zynaptik2_top.jpg|900px]]
@@ Line 25: / Line 27: @@
 '''+ ADS1115 (MOD-1 Analog Input):''' It uses I2C address 0x48 by default. The 4 analog input pins are labelled as ADx on the Zynaptik's header schematic.
-You can assign the Analog Inputs to MIDI events like Pitch-Bending, CC or ChanPress. This can be used for connecting CV-IN or for controlling sound engine parameters using analog sensors.
+The voltage range is 0-5V. You can assign the Analog Inputs to MIDI events like Pitch-Bending, CC or ChanPress and use the analog signals for controlling any sound parameter. Analog Inputs can be combined with digital inputs from the MCP23017, allowing to configure up to 4 x CV/Gate-IN interfaces.
-'''+ MCP4728 (MOD-2 Analog Output):''' It uses I2C address 0x60 by default. The 4 analog output pins are labelled as DAx on the Zynaptik's header schematic.
+'''+ MCP4728 (MOD-2 Analog Output):''' It uses different I2C address (0x60/0x61/0x64) depending of the zynaptik model. The 4 analog output pins are labelled as DAx on the Zynaptik's header schematic.
-It's being implemented currently and it's not available on zynthian software yet.
+The voltage range is 0-5V. You can assign MIDI events, like Pitch-Bending, CC or ChanPress, to the Analog Outputs. Analog Outputs can be combined with digital outputs from the MCP23017, allowing to configure up to 4 x CV/Gate-OUT interfaces.
 <br clear=all>

@@ Line 33: / Line 33: @@
 <br clear=all>
-=== Installing Zynaptik Expander Kit ===
+=== Installing Zynaptik-1 Expander Kit ===
 [[File:Zynaptik_kit_insert_header.png|300px|right]]
-The core Zynthian kit is designed to allow novice to build a full device. Beware that the Zynaptik expander kit installation is more challenging, requiring some electronic construction skills including soldering and cutting. An intermediate hobbyist should be able to tackle the installation.
+The core Zynthian kit is designed to allow novice to build a full device. Beware that installing the "Zynaptik-1 Expander Kit" is more challenging, requiring some electronic construction skills including soldering and cutting. An intermediate hobbyist should be able to tackle the installation.
 Insert one of the 10-pin 90 degree headers into the ADS1115 module. The pins go into the component side of the PCB extended through to the solder side. The ADS1115 is on the bent pin side of the header's plastic strip, not the straight pin side.
@@ Line 54: / Line 54: @@
 [[File:Zynaptik_kit_MCP23017_pin1.png|300px|right]]
-If your Zynaptik board is installed in your Zynthian, remove all the cables from the Zynaptik board then remove the board from the case by removing the four fixing screws.
+If your Zynaptik-1 board is installed in your Zynthian, remove all the cables from the Zynaptik-1 board then remove the board from the case by removing the four fixing screws.
-It is advised to use a 28-pin IC socket (not supplied) to mount the MCP23017 chip. This will reduce the risk of damage to the chip. Be aware that 28 pin sockets are available in different sizes. The dual-in-line narrow socket is required. You may solder the IC directly to the PCB if preferred. (You may use two 14-pin sockets (or another combination) if you do not have a 28 pin socket.) Insert the IC socket or the MCP23017 into the Zynaptik board. The socket should have a notch or indicator at one end. The MCP23017 has a dot near pin 1. This should be oriented towards the edge of the PCB. There is an outline of the IC drawn on the PCB with a notch in one end. This should align with the notch of the socket and the dot of the MCP23017. The component should sit on the same side of the Zynaptik board as the other components like the header pins.
+It is advised to use a 28-pin IC socket (not supplied) to mount the MCP23017 chip. This will reduce the risk of damage to the chip. Be aware that 28 pin sockets are available in different sizes. The dual-in-line narrow socket is required. You may solder the IC directly to the PCB if preferred. (You may use two 14-pin sockets (or another combination) if you do not have a 28 pin socket.) Insert the IC socket or the MCP23017 into the Zynaptik-1 board. The socket should have a notch or indicator at one end. The MCP23017 has a dot near pin 1. This should be oriented towards the edge of the PCB. There is an outline of the IC drawn on the PCB with a notch in one end. This should align with the notch of the socket and the dot of the MCP23017. The component should sit on the same side of the Zynaptik-1 board as the other components like the header pins.
 Solder the socket or MCP23017 in place. Use the previous tip of soldering one pin first then reflowing to ensure the component is fitted snug against the board. WARNING: If soldering the MCP23017 directly to the PCB be careful to apply heat for a very short period (approx. 2s) to each pin. Integrated circuits are fragile and can be damaged by heat. Tip: The MCP23017 is supplied inserted in a piece of foam. Use this to support the IC socket or MCP23017 whilst soldering.
@@ Line 70: / Line 70: @@
 [[File:Zynaptik_kit_child_boards.png|300px|right]]
-Insert the ADS1115 module into the Zynaptik board from the component side with its pin 1 ('V') inserted into the hole with the square line around it, nearest the label, "MOD-1". Insert the MCP4728 module into the Zynaptik board from the component side with its pin 1 ('V') inserted into the hole with the square line around it, nearest the label,  "MOD-2".
+Insert the ADS1115 module into the Zynaptik-1 board from the component side with its pin 1 ('V') inserted into the hole with the square line around it, nearest the label, "MOD-1". Insert the MCP4728 module into the Zynaptik-1 board from the component side with its pin 1 ('V') inserted into the hole with the square line around it, nearest the label,  "MOD-2".
 Support the modules with your fingers whilst turning the board over then solder the 10 pins of each board. Be careful to avoid prolonged (approx. 2s) heat applied to each pin.
@@ Line 76: / Line 76: @@
 If using an IC socket, insert the MC23017 into the socket. This can be awkward because the pins may splay too far. Gently locate all 14 pins on one side of the MC23017 in the jaws of the socket then supporting the whole of the MC23017 with your fingers press to bend the pins slightly to locate the other row of 14 pins in their corresponding socket jaws. Only when all 28 pins are located, gently but firmly press the MC23017 into the socket with even pressure over the whole chip.
-Install the Zyanptic board into the Zynthian. Use a 40 pin IDC DIL connector with ribbon cable to extend the "Zynaptic-1" connector through the slot in the front of the Zynthian case. You will need to build your own external hardware interface.
+Install the Zynaptik-1 board into the Zynthian. Use a 40 pin IDC DIL connector with ribbon cable to extend the "Zynaptik-1" connector through the slot in the front of the Zynthian case. You will need to build your own external hardware interface.
 <br clear=all>

← Older revision		Revision as of 10:26, 26 October 2021
Line 156:		Line 156:


−	[[ File:Wyleu pedalboard program change switches.jpg\|~~400px~~\|right]]	+	[[ File:Wyleu pedalboard program change switches.jpg\|600px\|right]]

−	[[File:Zynaptik config analog in.png\| ~~400px~~\| right]]	+	[[File:Zynaptik config analog in.png\| 600px\| right]]

@@ Line 144: / Line 144: @@
 The zynaptik Analogue inputs can be used to generate MIDI CC control from a Standard Control Pedal.
-[[File:IMG 20210825 165908.jpg|400px|right]]
+[[File:IMG 20210825 165908.jpg|600px|right]]
-[[File:Zynaptik control deal input settings.png|400px|right]]
+[[File:Zynaptik control deal input settings.png|600px|right]]

@@ Line 125: / Line 125: @@
-[[File:Successful testing zynaptik in.png|400px|right]]
+[[File:Successful testing zynaptik in.png|600px|right]]
 Notice:
@@ Line 132: / Line 132: @@
 Interrupts default (27/25).
 Zynaptik Config:
-[[File:Zynaptic config wyleu-pedal.png|400px|right]]
+[[File:Zynaptic config wyleu-pedal.png|600px|right]]
 <br clear=all>

@@ Line 120: / Line 120: @@
 With the testing branch selected.
@@ Line 136: / Line 139: @@
 It is used to
 <br clear=all>
 ===Connect up to 4 Control pedals===

@@ Line 148: / Line 148: @@
 ===Eight digital input switches selecting Program Change events===
 [[ File:Wyleu pedalboard program change switches.jpg|400px|right]]
 [[File:Zynaptik config analog in.png| 400px| right]]