2,703
edits
Changes
Jump to navigation
Jump to search
mLine 14:
Line 14: − + − + − + Line 78:
Line 78: − + + Line 87:
Line 88: − + − + Line 112:
Line 113: − + − These are 2 separated connectors with a 3-wire harness each, ended with 3 x 1-pin DuPont connectors. One of them have a '''red circle sticker that MUST be mounted on the Right (R) audio Out'''"+ − − Insert the jack connectors into the 2 holes labelled as ''audio OUT''. You have to insert them from inside the case and secure them with the washers and nuts from the outside. The washers will keep the nut from damaging the case. Use a wrench for tightening the nuts, but not too much!! − − − [[File:Zynthian_case_connectors_v41_red.jpg|400px]] − [[File:IMG_2890_OK_1024_fixv41.JPG|400px]] − [[File:IMG_2895_OK_1024_red.JPG|400px]] − − ===Secure the balanced audio input jack-TRS connectors=== − These are 2 separated connectors with a 3-wire harness each, ended with 3 x 1-pin DuPont connectors.+ + + − Insert the jack connectors into the 2 holes labeled as ''audio IN''. You have to insert them from inside the box and secure them with the washers and nuts from the outside. The washers will keep the nut from damaging the case. Use a wrench for tightening the nuts, but not too much!+ − + − − [[File:IMG_2886_OK_1024.JPG|400px]] − − Line 220:
Line 210: − + − − {{NoteBox|Note that the Hifiberry DAC+ADC Stage included in the 4.1 kit has no RCA connectors. Photos may show an older model, but these instructions are accurate for V4.1. }} Line 300:
Line 288: − + − Every TSR connector has 3 colored wires like this:+ − * '''Red''' -> Signal + − * '''White''' -> Signal - − * '''Black''' -> Ground − Each TSR connector must be connected to the 10-pin header (J1) on the Hifiberry DAC+ADC Stage:+ − [[File:HifiBerryDACADC-Stage-header.jpg|450px]] − First, connect the audio OUT TSR connectors like this:+ − + − − And then, the audio IN TSR connectors like this: − − [[File:HifiBerryDACADC-Stage-connection-IN.png|600px]]
Building a Zynthian Box using official Kits v4.2-v4.6 (view source)
Revision as of 10:48, 15 July 2021
, 10:48, 15 July 2021Jofemodo moved page Building a Zynthian Box using an official Kit v4.2 & v4.3 to Building a Zynthian Box using an official Kits v4.2, v4.3 & v4.4
** [https://www.raspberrypi.org/products/ Raspberry 4 Computing Board]
** [https://www.raspberrypi.org/products/ Raspberry 4 Computing Board]
** [https://www.hifiberry.com/docs/data-sheets/datasheet-dac-adc-stage/ HifiBerry DAC+ADC STAGE souncard]
** [https://www.hifiberry.com/docs/data-sheets/datasheet-dac-adc-stage/ HifiBerry DAC+ADC STAGE souncard]
** [https://shop.zynthian.org/shop/product/zynaucon-module-v4-2-406?category=16 ZynAuCon Module] (audio connectors board)
** [https://shop.zynthian.org/shop/product/zynaucon-module-406?category=16 ZynAuCon Module] (audio connector board)
** [https://shop.zynthian.org/shop/product/zynscreen-v1-5-361?category=16 ZynScreen v1.5] (3.5" touch-display + controllers I/O + rubber silicon button)
** [https://shop.zynthian.org/shop/product/zynscreen-v1-5-361?category=16 ZynScreen v1.5] (3.5" touch-display + controllers I/O + rubber silicon button)
** [https://shop.zynthian.org/shop/product/zynthian-controllers-v4-328?category=16 4 x controllers v4]
** [https://shop.zynthian.org/shop/product/zynthian-controllers-v4-328?category=16 4 x controllers v4]
** [https://shop.zynthian.org/shop/product/zynaptik-module-330?category=16 Zynaptic module] (MIDI IN/THRU/OUT & extended I/O)
** [https://shop.zynthian.org/shop/product/zynaptik-module-330?category=16 Zynaptic module] (MIDI IN/THRU/OUT & extended I/O)
** Aluminum Case v4 (including zynductor passive cooling, bolts & nuts)
** [https://shop.zynthian.org/shop/product/aluminum-case-kit-v4-1-333?category=13 Aluminum Case v4] (including zynductor passive cooling, bolts & nuts)
** [https://shop.zynthian.org/shop/product/zynthian-case-connectors-kit-v4-363?category=16 Pre-built case-connectors] (with soldered harnesses)
** [https://shop.zynthian.org/shop/product/zynthian-case-connectors-kit-v4-363?category=16 Pre-built MIDI case-connectors] (with soldered harnesses)
** [https://shop.zynthian.org/shop/product/zynthian-ribbon-bus-cable-278?category=16 Ribbon bus cable]
** [https://shop.zynthian.org/shop/product/zynthian-ribbon-bus-cable-278?category=16 Ribbon bus cable]
* Power supply for RBPi 4 (5.1v 3A with USB type-C connector) => Not included on official kits!
* Power supply for RBPi 4 (5.1v 3A with USB type-C connector) => Not included on official kits!
===Zynthian Kit v4===
===Zynthian Kit v4===
A Zynthian Kit is a set of electronic and mechanic parts. The ''official'' Zynthian Kit v4 consists of these parts:
A Zynthian Kit is a set of electronic and mechanic parts. The ''official'' Zynthian Kit v4.2 consists of these parts:
+ '''1 x Raspberry Pi 4'''
+ '''1 x Raspberry Pi 4'''
+ '''1 x Hifiberry DAC+ADC PRO'''
+ '''1 x Hifiberry DAC+ADC PRO'''
+ '''1 x ZynAuCon Module + Mini-ribbon cable'''
+ '''1 x ZynScreen v1.5:''' Touch-Display 3.5" + Controllers circuit + Silicone buttons
+ '''1 x ZynScreen v1.5:''' Touch-Display 3.5" + Controllers circuit + Silicone buttons
+ '''4 x Controller Modules + Wiring'''
+ '''4 x Controller Modules + Wiring'''
+ '''1 x Ribbon bus cable'''
+ '''1 x Ribbon bus cable'''
+ '''1 x Zynthian Aluminium Case'''
+ '''1 x Zynthian Aluminium Case'''
+ '''1 x Connectors Set'''
+ '''1 x MIDI Connectors Set + LEDs'''
+ '''1 x Bolts & Nuts Set'''
+ '''1 x Bolts & Nuts Set'''
+ '''1 x Zynductor'''
+ '''1 x Zynductor'''
[[File:Rbpi4 shop.jpg|330px]][[File:HifiBerryDACADC-Stage-top.jpg|330px]][[File:IMG_2775_OK_shop.JPG|330px]][[File:Controllers_shop.jpeg|330px]][[File:Zynaptik shop.jpeg|330px]][[File:Ribbon_shop.jpeg|330px]][[File:Zynthian_alucase_v41-persp.jpg|330px]][[File:Zynthian_case_connectors_v41.jpg|330px]][[File:Boltsnuts.JPG|440px]][[File:IMG_2756_OK_shop.JPG|220px]]
[[File:Rbpi4 shop.jpg|330px]][[File:HifiBerryDACADC-Stage-top.jpg|330px]][[File:IMG_2775_OK_shop.JPG|330px]][[File:Controllers_shop.jpeg|330px]][[File:Zynaptik shop.jpeg|330px]][[File:Ribbon_shop.jpeg|330px]][[File:Zynthian_alucase_v41-persp.jpg|330px]][[File:ZynAuCon miniribbon.jpg|400px]][[File:IMG_2887_OK_1024.JPG|400px]][[File:Boltsnuts.JPG|440px]][[File:IMG_2756_OK_shop.JPG|220px]]
===Unboxing the Zynthian Kit v4===
===Unboxing the Zynthian Kit v4===
Let's go!!
Let's go!!
===Secure the balanced audio output jack-TS connectors ===
===Secure the ZynAuCon Audio Connector Board ===
The ZynAuCon module improves and simplifies the audio wiring by using a small ribbon cable for driving the 4 balanced channels (2 inputs + 2 outputs) to the 4 high-quality Neutrik TSR case-connectors. For mounting the ZynAuCon, secure the 2 x 15mm separators with 2 x black-anodized bolts M2.5. Next, you have to insert the board from inside the case and secure them with the 4 x nuts from the outside. Use a wrench for tightening the nuts, but not too much, and take care of not damaging the surface of the nice aluminum case!!
[[File:IMG_3419_fixed.JPG|200px]]
[[File:IMG_3355_fixed.JPG|400px]]
[[File:IMG_3387_fixed.JPG|400px]]
[[File:IMG_3395_fixed.JPG|400px]]
[[File:IMG_3401_fixed2.JPG|500px]]
[[File:IMG_2896_OK_1024_fixv41.JPG|400px]]
[[File:IMG_2898_OK_1024.JPG|400px]]
===Secure the MIDI connectors===
===Secure the MIDI connectors===
{{NoteBox|The Hifiberry DAC+ADC Stage may include some nylon spacers and bolts. You can choose to use these instead of the metal ones included with the Zynthian kit. }}
{{NoteBox|Note that the "Hifiberry DAC+ADC Stage", included in the 4.1, 4.2 & 4.3 kits, and the "ZynADAC", included in the 4.4 kit, have no RCA connectors. Photos may show an older model, but these instructions are accurate for 4.1 to 4.4 kits. }}
===Secure the Zynaptik module===
===Secure the Zynaptik module===
===Connect the TSR Balanced Audio Connectors to the Hifiberry DAC+ADC Stage===
===Connect the ZynAuCon module to the Hifiberry DAC+ADC Stage===
Plug the little 2x10 ribbon cable on the Hifiberry's J1 connector. Next, plug the other end on the ZynAuCon board. Observe that the ribbon cable must be bent forming a 90º angle, so it fits perfectly the space and distance between the 2 IDC connectors.
[[File:IMG_3410_fixed.JPG|600px]]
FYI, this is the specification for the 10-pin header (J1) on the Hifiberry DAC+ADC Stage:
[[File:HifiBerryDACADC-Stage-connection-OUT.png|600px]]
[[File:HifiBerryDACADC-Stage-header.jpg|450px]]
===Connect the Display===
===Connect the Display===