Changes

* '''SD-Card >= 16GB (NOT included in V5 kit)'''

* '''SD-Card >= 16GB (NOT included in V5 kit)'''

* Optional: CR2032 lithium battery (NOT included in V5 kit)

* Optional: CR2032 lithium battery (NOT included in V5 kit)

<br clear=all>

<br clear=all>

<br clear=all>

<br clear=all>

=='''Sticking the rubber feet to the aluminum case bottom'''==

=='''Stick the rubber feet to the aluminum case bottom'''==

<br clear=all>

<br clear=all>

<br clear=all>

<br clear=all>

=='''Install the display ribbon cable to the RPi4'''==

=='''Plug the display ribbon cable into the RPi4'''==

<br clear=all>

<br clear=all>

[[File:IMG_4135_fixed_wiki.JPG|600px|right]]

[[File:IMG_4135_fixed_wiki.JPG|600px|right]]

'''3.''' Open the RPi4's DSI connector by softly pulling both sides of the tiny black tongue at once. When it's totally open, push the ribbon cable inside, straight, with the blue side facing out. When the cable is tightly inserted, close the connector by pushing the tongue with 2 fingers, one of each hand. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK.

'''3.''' Open the RPi4's DSI connector by softly pulling both sides of the tiny black tongue at once. When it's totally open, push the ribbon cable inside, straight, with the blue side facing out. '''All flat cables in the V5 kit are reversible, so you can take any of the 2 caps''', while taking care of placing the blue side facing out. When the cable is tightly inserted, close the connector by pushing the tongue with 2 fingers, one of each hand. Pay attention to ensure the cable does not move out of the connector. If it's not well inserted or not straight, repeat the operation until it's OK.

<br clear=all>

<br clear=all>

[[File:capture000068_fixed_wiki.JPG|600px|right]]

[[File:capture000068_fixed_wiki.JPG|600px|right]]

'''4.''' Secure the 8 x spacers in the control board's top side. To do this, insert the bolt from the back side and while holding it with your finger, fasten the spacer with the other hand until it's tight. You don't need a wrench for this, but you can use one if you like.

'''4.''' Secure the 8 x spacers on the control board's top side. To do this, insert the bolt from the back side and while holding it with your finger, fasten the spacer with the other hand until it's tight. You don't need a wrench for this, but you can use one if you like.

<br clear=all>

<br clear=all>

[[File:capture000086_fixed_wiki.jpg|600px|right]]

[[File:capture000086_fixed_wiki.jpg|600px|right]]

'''3.''' Insert the ribbon cable into the FPC connector. It must be inserted straight, with the blue side face down.

'''3.''' Insert the ribbon cable into the FPC connector. It must be inserted straight, with the blue side facing down. '''All flat cables in the V5 kit are reversible, so you can take any of the 2 caps''', while taking care of placing the blue side facing down.

<br clear=all>

<br clear=all>

[[File:capture000089_fixed_wiki.jpg|600px|right]]

[[File:capture000089_fixed_wiki.jpg|600px|right]]

'''3.''' Place the silicone buttons in place, on top the control board. Note the tiny silicone nipples in the bottom and pay attention to get them to fit into the small locating-holes on the control board. Once it's done, softly side-push to check the buttons are well sited in place. They shouldn't move.

'''3.''' Place the silicone button pad on top the control board. Note the tiny silicone studs in the bottom of the pad and pay attention to make them fit into the small positioning holes on the control board. Once it's done, softly push the button pad to the side to check whether it sits snug in it's place. The pad shouldn't move when you try pushing it to the side.

<br clear=all>

<br clear=all>

[[File:capture000123_fixed_wiki.jpg|600px|right]]

[[File:capture000123_fixed_wiki.jpg|600px|right]]

'''3.''' Close the case slowly, taking care that the cables are not being trapped.  

'''3.''' Close the case slowly, taking care that the cables are not being trapped.

 

 

 

 

 

Once you see the splash screen, it could take some minutes until the system is ready. You deserve a beer, or at less some some tea or coffee. When the first-boot process finishes, the zynthian will reboot and you will be in the main menu, ready to play.

<br clear=all>

<br clear=all>

[[File:capture000125_fixed_wiki.jpg|600px|right]]

[[File:capture000125_fixed_wiki.jpg|600px|right]]

'''4.''' Take the remaining 6 x ISO7380 M3 screws and secure the case, 3 on each side. Tighten enough, but not too much.

'''5.''' If everything worked fine and your zynthian booted, finish the task before start exploring your new zynthian V5. Take the remaining 6 x ISO7380 M3 screws and secure the case, 3 on each side. Tighten enough, but not too much.

<br clear=all>

<br clear=all>

[[File:capture000136_fixed_wiki.jpg|600px|right]]

[[File:capture000136_fixed_wiki.jpg|600px|right]]

'''4.''' Turn the 4 x rotary encoders until the flat cotter is pointing outside.  

'''4.''' Turn the 4 x rotary encoders until the flat cotter is pointing outside.  

[[File:capture000140_fixed_wiki.jpg|600px|right]]

[[File:capture000140_fixed_wiki.jpg|600px|right]]

<br clear=all>

<br clear=all>